FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-33

PDF page 302 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 302
AC 27-1B · D-33Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

especially helpful in determining clearance during autorotation and controllability testing
under FAR 27.143.  If such measuring devices are used, the type inspection report
should contain a record of clearance found during the tests. During TIA flight testing, it
is not necessary to precisely determine the clearance but only necessary to determine
"enough clearance" as stated in the rule.

AC 27.663  § 27.663 (Amendment 27-2) GROUND RESONANCE PREVENTION
         MEANS.

     a. Explanation.

         (1) This rule, adopted in Amendment 27-2 and revised in Amendment 27-26
requires reliability and damping action investigation for the ground resonance
prevention means. The probable range of variations in service, not just the allowable
range, must be established and investigated as prescribed. This probable range
includes operation on the ground, and other appropriate landing surfaces applicable to
the rotorcraft design shall be considered. Quantitative test data are generally obtained
in compliance with this rule, but analysis or tests may be used.

         (2) Appropriate maintenance information should be included in the
maintenance manual (also called instructions for continued airworthiness).

         (3) Paragraph AC 27.241 of this document concerns demonstrating freedom
from ground resonance during certain applicant and TIA verification evaluations or tests
of the rotorcraft. Section 27.241 complements the requirements of § 27.663. As noted
in paragraph AC 27.241 of this document, a specific requirement for a ground vibration
survey was removed from CAR Part 6. However Section 27.663 was adopted by
Amendment 27-2 to investigate possible sources of ground resonance and to assure
the reliability of the ground resonance prevention means, i.e., dampers, if necessary, to
preclude occurrence of ground resonance. The total rotorcraft system is evaluated
under this rule.

         (4) Viscous dampers have been used for many years to prevent ground
resonance. Modern rotorcraft designs may also use elastomeric dampers and may use
elastomeric bearings in the rotor head and rotor pylon attachment to the airframe. The
rule also requires investigation of the probable range of variations of these dampers,
whether viscous or elastomeric, and these bearings to preclude ground resonance.

         (5) Ground resonance can occur due to flexibility in the rotor pylon restraint
system as well as with landing gear flexibilities. See paragraph b(2) of this guidance
section (AC 27.663) for an explanation. An analysis may be done to show the effect of
the rotor pylon mount stiffness on ground resonance stability.  If the analysis shows that
rotor pylon mount stiffness could affect ground resonance, the evaluation should include
variations in stiffness and damping of the rotor pylon restraints that may occur in service
(reference “Ground Vibrations of Helicopters,” M.L. Deutsch, JAS, Vol. 13, No. 5, May
1946).


                                                       Page D - 33

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →