FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-28

PDF page 297 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 297
AC 27-1B · D-28Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

1.85 = 8,894 PSI.  If a free or loose fit is not used; i.e., tighter than free fit, a bearing
factor is not required. See paragraph AC 27.623a(4) for bearing factors.

         (4) Military standard part specifications, MS 21240, “Bearing, Sleeve Plain, TFE
Lined,” and MS 21241, “Flanged Bearing, Sleeve Plain, TFE Lined,” contain allowable
load ratings, static and dynamic, that apply to the particular use of the bearing. An
appropriate bearing factor should be applied to the static rating. Military Specification
(MIL-B-8943A, Amendment 3, “Bearing, Sleeve, Plain, and Flanged, TFE Lined”
(temperature range -65° F to +250° F) shows that MS 21240 and MS 21241 sleeve
bearings have been superseded by MS 1934/1 and MS 81934/2 sleeve bearings,
respectively. Military Specification MIL-B-81934, Amendment 2, “Bearings, Sleeve,
Plain and Flanged, Self-Lubricating,” uses TFE liners. These bearings are intended for
use in a temperature range from -65° F to +325° F. Whenever a sleeve bearing is used,
an appropriate bearing factor should be applied to the static rating that is contained in
the specification or standard. Other sleeve bearings are contained in standards NAS 72
through NAS 77, NAS 537, and NAS 538. The installation design information is only
contained in standards NAS 72 through NAS 74. These types of plain sleeve bearings
are designed for clamping to the shaft or bolt with relative motion occurring on the
bearing outside diameter. An appropriate bearing factor is required for the application.

         (5) The minimum fitting factor 1.15, specified by § 27.625, must be applied as
specified to account for load distribution at the fitting. This fitting factor need not apply
to plain or journal “bearings” whose “bearing factor” exceeds 1.15.

         (6) For airframe and landing gear structural joints, the manufacturer’s static,
non-Brinell rating of ball and roller bearings should not be exceeded. ABEC Class 1
bearings or better quality bearings may be used in airframe structural joints and landing
gear; ABEC Class 3, 5, or 7 bearings should be used in rotor pivot joints. The
non-Brinell rating includes consideration of the bearing factor, and no other bearing
factor is necessary.

         (7) A free fit was described in American Standards Association (ASA) Standard
B4a-1925. The “free fit” clearances and tolerances of this old standard are now called
Class RC6, Medium Running Fit, in ASA Standard B4.1, 1955. As an illustration using
these standards, a 1-inch diameter shaft and a plain sleeve bearing would have a
clearance ranging from 0.0014 to 0.0040 inch.

AC 27.625.  § 27.625 FITTING FACTORS.

     a. Explanation. A 1.15 factor is specified to ensure that the calculated load and
stress distribution within any fitting is conservative. Application of the factor is excluded
or is an exception as stated in the rule.

     b. Procedures.

         (1) The factor may be applied to the calculated load or stress for the fitting.


Page D - 28

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →