FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-29

PDF page 298 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 298
AC 27-1B · D-29Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


         (2) The structural design substantiating data should include the fitting factor
and where applicable should include, but not be limited to, the rotor system. The rotor
system includes the rotor blade attachments, rotor head and hubs, and boosted control
system elements. Other typical areas that may be considered are tail rotor gearbox
attachment, tailboom to fuselage fittings, transmission pylon attachments, and landing
gear attachment to the rotorcraft.

         (3) The fitting factor is not required in the following applications:

                  (i)    Joints such as continuous joints in metal plating, welded joints and
scarf joints in wood.

                   (ii)   Elements proven by limit or ultimate load tests such as nonboosted
control system parts.

                    (iii)  Elements for which a larger load factor is used such as a casting
factor, a 1.33 retention factor when required for seats and safety belts, a fatigue factor,
bearing factor or special factor greater than 1.15, crash load factors that are the only
design case, and crash load factors that exceed limit load factors x 1.5 x 1.15.

               (iv)  Elements for which the failure mode does not affect safety of flight or
occupant safety.

AC 27.625A § 27.625 (Amendment 27-35) FITTING FACTORS.

     a. Explanation. Amendment 27-35 added § 27.625(d) that requires a 1.33 factor
applied to the emergency landing loads of § 27.561(b)(3) for the substantiation of
attachments of each seat, berth and litter to the structure and each safety belt or
harness to the seat, litter, or structure.

     b. Procedures. All of the advisory material pertaining to this section remains in
effect with the following additions.

         (1) A fitting factor of 1.33 must be applied to the emergency landing loads of
§ 27.561(b)(3) when evaluating the attachments of the seat, berth, and litter to the
structure, and each safety belt and harness attachment to the seat, berth, litter, or
structure.

         (2) The 1.33 factor is required whether analysis or test is used.

AC 27.629.  § 27.629 FLUTTER.

     a. Explanation. The rule requires that the rotorcraft “be free from flutter under
each appropriate speed and power condition.”



                                                       Page D - 29

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →