FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-27

PDF page 296 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 296
AC 27-1B · D-27Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

AC 27.623.  § 27.623 BEARING FACTORS.

     a. Explanation.

         (1) The rule requires use of a minimum bearing factor in free fit joints to
account for effects of typical relative motion. A minimum value is not specified in the
rule. The factor, appropriate for the application, is applied to the ultimate bearing
strength of the softest material used as a bearing. A definition of free fit (clearance fit) is
noted in paragraph AC 27.623b(7) below.

         (2) A bearing factor, appropriate for the application, shall be used unless a
larger factor is used.

         (3) For reference, specific bearing factors are contained in § 29.685(e) for
transport rotorcraft control system joints subject to angular rotation. These factors are
applied to the ultimate bearing strength of the softest material used as a bearing in the
control system. Control systems ball, roller, or needle bearings are covered by
§ 29.685(f) for transport rotorcraft.

         (4) MIL-HDBK-5D, paragraph 8.3, refers to design standards for plan or journal
bearings or bushings. These standards are found in Air Force Systems Command
Design Handbook AFSC DH-2-1, Airframe, Chapters 3 and 6.

     b. Procedures.

         (1) Control system joint bearings are discussed under § 27.685 and
paragraph AC 27.685A, but the bearing factors are noted here for convenience. For
transport rotorcraft control systems, § 29.685(e) requires a 2.0 bearing factor for cable
systems and a 3.33 bearing factor for push-pull systems other than ball and roller
bearing systems. The manufacturer’s static, non-Brinell rating of ball and roller bearings
should not be exceeded. Use of this for normal category rotorcraft is recommended.

         (2) A landing gear pivot, grease-lubricated, plain bearing is one example of a
free fit subject to pounding or vibration. A bearing factor of 2.0 may be used or another
factor may be proven for a grease-lubricated plain bearing or bushing to account for the
anticipated higher loads caused by pounding or vibration. See
paragraph AC 27.623b(6) for recommendations on ball or roller bearings.

         (3) A typical engine mount bolt installation with a plain bearing having a free or
loose fit (not interference fit) is another example of a sleeve bearing application subject
to a design bearing factor. As an EXAMPLE OR ILLUSTRATION, a bearing factor of
1.85 may be applied to the design loads on the softest material reacting the bearing
loads. A different but appropriate factor will be acceptable. The design limit load may
be calculated for the example of a 0.312-inch-diameter bolt in a 2-inch-long bearing.
The bearing projected area is 0.312 x 2 = 0.624-square-inches. The design limit load is
3,000 pounds. The design limit bearing stress is 3,000 pounds/0.624-square-inch x


                                                       Page D - 27

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →