FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-21

PDF page 290 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 290
AC 27-1B · D-21Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


The test loads will be applied and reacted using mating aircraft parts or special fixtures
which simulate the mating parts. The methods and apparatus to be used for the static
tests of the castings are discussed in the apparatus and method section of this report.

Testing will be conducted in . . . (location).

                        TEST SPECIMEN

The castings which will be tested are listed in numerical order in figure AC 27.621-2.
Those castings which, after structural analysis, show less than a 1.5 casting factor will
be tested.  All directions are given with reference to a forward facing position in the
rotorcraft.

On the basis of a radiographic examination, the three castings which are of the poorest
acceptable quality in the first production lot of castings will be selected as test
specimens. The poorest of the three castings will be selected as the initial test casting
and its radiograph or ASTM standard will be used as the standard for accepting future
castings of the particular part unless later standards are approved. Three castings must
be tested for each critical condition for each part.

Conformity Inspection

Each machined casting will be subjected to an FAA/AUTHORITY conformity inspection
prior to testing to determine compliance with the type design drawings. A conformity
report for each casting may be incorporated in Part II, Test Results, of this report.

The test specimen will be permanently marked or defaced after testing to preclude its
use on a rotorcraft.

See figure AC 27.621-2 for an example of a convenient means of listing castings.

                          TEST LOAD

The test load(s) to be applied to each casting represents the critical loading condition(s)
for that casting. The critical conditions on each of the castings were determined by the
design criteria and substantiating data approved by the FAA/AUTHORITY.

The design criteria for all of the castings to be static tested may fall into one of two
categories. The load factors and structural acceptability requirements for each category
are discussed below. Casting factors that are included on the load sheets of each part
do not apply in the discussion below. (See paragraph AC 27.621b(2) for casting
factors.)





                                                       Page D - 21

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →