FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-20

PDF page 289 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 289
AC 27-1B · D-20Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99


    <(6)>  Each casting shall receive 100 percent visual and reduced
            radiographic and magnetic particle or penetrant inspection or approved
            equivalent methods.

    <(7)>  Each casting shall receive 100 percent inspection by visual,
            radiographic, and magnetic particle or penetrant inspections or approved
            equivalent methods.

    <(8)>  Three sample castings shall be static tested and shown to meet:

         No failure at 1.25 x 1.5 x limit load, and
           no yielding at 1.15 x limit load.

    <(9)>  Castings shall be procured to a specification that guarantees the
           mechanical properties of the material in the casting and provides
           demonstration of these properties by test of coupons cut from the castings
          on a sampling basis.

This chart may be included in the casting test proposal report.  It is recommended that
the applicant include in the test proposal report additional information such as shown in
paragraph AC 27.621b(3).

         (3) The casting test report may include the following sections or items in a
Part I of the report. The report may also have a Part II that contains the test results as
shown in the following example report. The following sections are a recommended
format content of the report. Appropriate changes should be made as desired to
accommodate the applicant’s system.

                     EXAMPLE OF REPORT
                        INTRODUCTION

This report presents the proposal for the static test of the castings used on the
Model XYZ. The castings will be tested in compliance with Federal Aviation
Regulations § 27.621. The purpose of this test is to substantiate the structural strength
of the castings used on the Model XYZ. Part II of this report, which will be published
after static tests have been completed, will present test results.

All test specimens will be selected as radiographic standards of acceptance for the
particular castings (see Test Specimen). Additional information on selecting the specific
castings may be included in the test specimen section of this report.

Load sheets giving direction and magnitude of loads for each of the castings are
presented in numerical order by part number at the end of this report. The test loads
and design criteria for the castings are discussed in detail in the test loads section of
this report.


Page D - 20

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →