Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
Castings Designed to Limit Load Conditions
A structural analysis of each test casting showing the critical design limit load conditions
is given in the data (reference report number here). The load factors for the static test
of the castings are as follows:
1.15 x design limit load = design yield load
1.50 x design limit load = design ultimate load
Castings Designed Only to Crash Landing Conditions
The castings in this category were designed using a crash landing load factor for the
design ultimate load. The design yield load criteria of 1.15 x limit load need not apply to
these castings. The test loads for these castings may be given in terms of design
ultimate load on the individual casting load sheets shown in Part I of this report.
Test Procedures
Depending on the results of the initial static test of each casting, the following procedure
will be used.
a. If in the initial test of critical castings the casting is found to have a casting
factor of 1.5 (1.5 x design ultimate load), the casting will be considered acceptable and
no further tests will be conducted.
b. If in the initial test(s) the critical casting is found to have a casting factor less
than 1.5 but equal to or greater than 1.25, two additional castings will be tested for each
critical load condition. Each must also show a minimum casting factor of 1.25.
c. If in the initial test, or in one of two additional tests, a casting shows a casting
factor less than 1.25 times design ultimate or yields prior to reaching 1.15 times design
limit load, the casting will be redesigned and retested. The yield criteria are also
applicable to the first two procedures with the exception of critical castings designed to
crash landing conditions.
TEST APPARATUS AND METHOD
The Model XYZ casting static tests will be conducted using fixtures designed to
simulate the installation of the castings in the aircraft. Where practical, mating aircraft
parts will be used to apply and react test loads. When practical, the static tests will be
conducted with mating castings assembled when the critical loads for the mating
castings are compatible; otherwise, fixtures simulating the mating parts may be
designed and fabricated for the tests. Assembly hardware used to mount test castings
will be the same as hardware used on the rotorcraft. All bolt torques and other
assembly notes will conform to the type design assembly instructions.
Page D - 22
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.