Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
AC 27.613. § 27.613 (Amendment 27-16) MATERIAL STRENGTH PROPERTIES
AND DESIGN VALUES.
a. Explanation. The rule requires the use of materials that have a known
minimum strength value. The structure must not be understrength and must be
designed to minimize fatigue failure.
(1) Material design values in certain specified documents may be used. The
FAA/AUTHORITY may approve other material design values thus allowing the applicant
greater flexibility in selection of materials by proving their strength properties and design
values as stated in § 27.613(d).
(2) Other materials that may be new or are not included in the specified
documents may be tested and design values established as provided by § 27.613(a)
and (d).
(3) Section 27.613(d) requires the selection of materials that will retain design
values and properties in the type of service environment and for the length of service
time intended for the structure.
(4) Section 27.613(c) is an objective rule concerning minimizing fatigue failures
and § 27.571 concerns quantitative fatigue substantiation requirements.
b. Procedures.
(1) The properties and design values in the documents noted in the rule may be
used.
(2) MIL-HDBK-5, Metallic Materials and Elements for Flight Vehicle Structure,
Chapter 9, contains procedures for establishing design values of additional materials.
Uniform means of presenting the data are also contained in this chapter.
(3) Design values and properties must include effects of the service
environment and service time. An example is exposure at elevated temperatures on the
ultimate tensile strength of 7079-T6 aluminum alloys as found in figure 3.7.4.1.1(c) of
MIL-HDBK-5.
(4) The probability of disastrous fatigue failures must be minimized. This may
be accomplished by using design features usually identified as fail-safe features, such
as the following:
(i) Selection of materials with stress levels to provide a controlled slow
rate of crack propagation combined with high residual strength after initiation of cracks
(lightly loaded structures).
Page D - 13
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.