FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-14

PDF page 283 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 283
AC 27-1B · D-14Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     3/31/2014


                   (ii)  Use of multipath construction and the provision of crack stoppers to
limit the growth of cracks.

                    (iii)  Use of composite (multielement) duplicate structures so that a fatigue
crack or failure occurring in one element of the composite (multielement) member will
be confined to that element and the remaining structure will still possess adequate
load-carrying ability.

               (iv)  Use of backup structure wherein one member carries all the load, with
a second member available and capable of assuming the extra load if the primary
member fails.

              (v)   Design to permit detection of cracks including the use of crack
detection systems, in all critical structural elements before the cracks can become
dangerous or result in appreciable strength loss, and to permit replacement or repair.

         (5) Acceptable standards for pressurized containers or cylinders, such as
cylinders of nitrogen, used to inflate emergency floats may be found in 49 CFR 178,
Subpart C, §§ 178.36 through 178.68. Specifically, § 178.44 concerns standards for
steel cylinders used in aircraft that are subjected to at least 900 PSI service pressure.
This standard includes strength, test, material property, inspection, quality, design
features, identification, and inspection report requirements. As an example,
§ 178.44-14, entitled “Hydrostatic Test,” requires that each cylinder must be (proof)
tested to at least 5/3 times the service pressure. Section 178.44-16, entitled “Burst
Test,” also states that one cylinder taken at random out of each lot of cylinders shall be
hydrostatically tested to destruction.

         (6) Other design criteria may be developed and approved under the provisions
of FAR Part 27 as a unique part of the aircraft type design.

AC 27.613A.  § 27.613 (Amendment 27-26) MATERIAL STRENGTH PROPERTIES
         AND DESIGN VALUES.

     a. Explanation. Amendment 27-26 added explicit probability standards criteria to
§ 27.613(b). This amendment also provided for testing or proving the strength of
selected individual items rather than conducting coupon tests to develop generic
material strength properties that would be used for design purposes.

     b. Procedures. The basic procedures of paragraph AC 27.613 still apply, except:

         (1) Probability criteria common with MIL-HDBK-5D are explicitly allowed to
determine strengths for metallic materials whose data are not available in
MIL-HDBK-5D. These specific probability criteria should be used in conjunction with
MIL-HDBK-17B whenever determining material strength properties for non-metallics.
(Also, reference paragraph AC 27 MG 8).



Page D - 14

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →