FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-9

PDF page 278 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 278
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                     AC 27-1B, Chg 4


                    (iii) Obtain FAA/AUTHORITY detail part conformity of the test articles and
installation conformity of applicable portions of the test setup. Obtain FAA/AUTHORITY
approval of the test proposal. A comprehensive test proposal may be used.

               (iv) Schedule FAA/AUTHORITY witnessing of the test or tests proposed.

              (v) Submit a test report describing all results and obtain FAA/AUTHORITY
approval of each report prepared.

         (2) Lightning Environment and Zones. AC 20-155 refers to SAE documents
ARP5412 (or EUROCAE ED-84) and ARP5414 (or EUROCAE ED-91), which provide
acceptable definitions for the rotorcraft lightning environment and for rotorcraft lightning
attachment zones.

         (3) Testing. Tests may be required to check the adequacy of the lightning and
electrostatic charge protection. Refer to SAE ARP5416 (or EUROCAE ED-105) for
acceptable test methods to show that the lightning protection is effective and to SAE
ARP5672 for acceptable test methods to show rotorcraft electrostatic charge control.

         (4) Aircraft Lightning Protection Design Features. The Aircraft Lightning
Protection Handbook (DOT/FAA/CT-89/22) provides information on aircraft lightning
protection design. The following are examples where lightning protection should be
considered.

                  (i) Rotors and Control Systems.

              (A) It should be established that an adequate bonding path exists between
the rotors and the airframe, such that a lightning strike to a rotor will not result in
damage to or seizure of gearbox or swashplate bearings, control jacks, etc.

              (B) Each hinge and bearing of rotor blades and control surfaces should
either:
                   (1) be capable of withstanding lightning without damage or seizure
leading to loss of function, or

                   (2) be provided with at least one bonding conductor, as flexible and
short as possible and installed so that there is no danger of the conductor jamming the
hinge or bearing following a lightning strike.

                   (ii) External Non-Metallic Parts.

              (A) Where non-metallic parts are fitted externally to the rotorcraft (e.g.,
rotors, radomes, composite skin panels) and may be subjected to lightning, they should
be protected. The protection should consider disruption of the materials because of:

                   (1) rapid expansion of gases within them (e.g., water vapor),


                                                           Page D - 9

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →