FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-10

PDF page 279 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 279
AC 27-1B · D-10Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     3/31/2014


                   (2) rapid build-up of pressure in voids or in the enclosure provided by
the parts resulting in mechanical disruption of the parts themselves or of the structure
enclosed by them, and

                   (3) fire caused by the ignition of the materials themselves or of the
materials contained within the enclosures.

              (B) Materials used for external non-metallic parts should have low water
absorption characteristics, should not occlude gases, and should be of high dielectric
strength in order to encourage surface flashover rather than puncture.

             (C) Rotors and other external parts of nonmetallic construction should be
provided with effective lightning conductors that are capable of safely carrying lightning
current, unless it can be shown that damage due to lightning will not endanger the
rotorcraft or its occupants. Bonding straps and leads are not required for small gaps
between metallic structure and diverters in non-conducting panels in order to comply
with the lightning protection criteria. However, an electrical bonding path may be
required to achieve static electricity protection.

         (5) Protection Against the Effects of Static Electricity.

                  (i) General. Rotorcraft structure, rotor systems, and equipment should be
electrically bonded together to minimize the accumulation and discharge of electrostatic
charge, which could result in electrical shock, ignition of flammable vapors, or
interference with essential equipment such as radio communications and navigational
aids.

                   (ii) Intermittent Contact. The design should prevent random intermittent
contact between metallic or metallized parts such that unwanted radio interference or
degradation of the components due to sparking will not occur.

                    (iii) Rotors and other external parts of nonmetallic construction should be
provided with effective electrical conductors that are capable of safely conducting
electrostatic charge.

               (iv) High Pressure Refueling and Fuel Transfer. Where provision is made
for high pressure refueling and/or high rates of fuel transfer, it should be established, by
test, or by consultation with the appropriate fuel manufacturers, that dangerously high
voltages will not be induced within the fuel system.  If compliance with this requirement
involves any restriction on the types of fuel to be used or on the use of additives, an
appropriate operating limitation should be established under § 27.1501(a). The critical
refueling rates are related to the rotorcraft refueling installations, and the designer
should seek the advice of fuel suppliers on this problem.



Page D - 10

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →