FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-117

PDF page 267 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 267
AC 27-1B · C-117Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

12/1/2011                                       AC 27-1B, Chg 4


         (3) The severity of the maneuvers investigated during the flight strain survey
should be at least as severe as the maneuvers likely to occur in service.

         (4) All flight conditions considered appropriate for the particular design are to
be investigated over the complete rotor speed, airspeed, center of gravity, altitude, and
weight ranges to determine the most critical stress levels associated with each flight
condition. The temperature effects on loads as affected by elastomeric components are
to be investigated. To account for data scatter and to determine the stress levels
present, a sufficient amount of data points should be obtained at each flight condition.
Consideration can be given to the use of scatter factors in determining the sufficiency of
data points. In some instances, the critical weight, center of gravity, and altitude ranges
for the various maneuvers can be based on past experience with similar design. This
procedure is acceptable where adequate flight tests are performed to substantiate such
selections. The combinations of flight parameters that produce the most critical stress
levels should be used in the evaluation.

   (vi) Frequency of loading.

           (A) Types of Operation.

               (1) The probable types of operation (transport, utility, etc.) for the rotorcraft
should be established. The type of operation can have a major influence on the loading
environment. In the past, rotorcrafts have been substantiated for the most critical
general types of operation with some consideration of special, occasional types of
operation. To assure that the most critical types of operation are considered, each
major rotorcraft structural component should be substantiated for the most critical types
of operation as established by the manufacturer. The types of operation shown below
should be considered and, if applicable, used in the substantiation:

                        (i) Long flights to remote sites (low ground-air-ground cycles but high
cruising speeds).

                          (ii) Typical, general types of operation.

                           (iii) Short flights as used in logging operations.

               (2) One means is to substantiate for the most severe type of operation;
however, this method is not always economically feasible.

               (3) A second means is to quantify the influence of mission type on fatigue
damage by adding to or replacing hour limitations by flight cycle limitations (if properly
defined and easily identifiable by the crew, for example: one landing, one load
transportation). A special type of flight hour limitation replacement using factorization of
flight hours for multiple types of operations may be feasible if continuing manufacturers’
technical support is provided and documented (i.e., the manufacturer either provides the



                                                         Page C - 117

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →