Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 12/1/2011
factorization analyses or checks them on a continuing basis for each type of rotorcraft
operation).
(4) Where one or more operations are not among the general uses
intended for the rotorcraft, the rotorcraft flight manual should state in the limitations
section that the intended use of the rotorcraft does not include certain missions or
repeated maneuvers (e.g., logging with its high number of takeoffs and landings per
hour). A note to this effect should also appear in the rotorcraft airworthiness limitations
section of the maintenance manual prepared in accordance with §§ 27.573
and 27.1529.
(5) Should subsequent usage of the rotorcraft encompass a mission
outside the original structural substantiation, the effects of this new mission environment
on the frequency of loading and structural substantiation should be addressed and
where practicable, in the interest of safety, a reassessment made. If this reassessment
indicates the necessity for revised retirement times, those new times may be limited to
specific rotorcraft model involved in the added mission provided:
(i) changes are adopted through the airworthiness directives process
and proper part re-identification is established; or
(ii) a Rotorcraft Flight Manual (RFM) supplement outlining the
limitations is approved; or
(iii) an airworthiness limitations section (ALS) supplement is approved;
or
(iv) an appropriate combination of part re-identification, RFM
supplement, or airworthiness limitation section supplement is approved.
(B) Loading Spectrum. The spectrum allocating percentage of time or frequencies of
occurrence to flight conditions or maneuvers is to be based on the expected usage of
the rotorcraft. This spectrum is to be established so that it is unlikely that actual usage
will subject the structure to damage beyond that associated with the spectrum.
Considerations to be included in developing this spectrum should include prior
knowledge based on flight history recorder data, design limitations established in
compliance with § 27.309, and recommended operating conditions and limitations
specified in the rotorcraft flight manual or instructions for continued airworthiness (ICA).
The distribution of times at various forward flight speeds should reflect not only the
relation of these speeds to VNE but also the recommended operating conditions in the
rotorcraft flight manual or ICA that govern Vc or cruise speed. It is desirable to conduct
the flight strain-gauge program by simulating the usage as determined previously, with
continuous recording of stresses and loads, thus obtaining directly the stress or load
spectra for structural elements.
(7) The seventh major area is the dynamic loading and response requirements of
§§ 27.241, 27.251, and 27.629 for vibration and resonance frequency determination and
Page C - 118
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.