Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 12/1/2011
(A) General. Subsequent to design analysis, in which aircraft loads and
associated stresses are derived, the stress level or loads are to be verified by a
carefully controlled flight strain measurement program. (This guidance is similar to that
of AC 27-1B, MG 11.)
(B) Instrumentation.
(1) The instrumentation system used in the flight strain measurement program
should accurately measure and record the critical strains under test conditions
associated with normal operation and specific maneuvers. The location and distribution
of the strain gauges should be based on a rational evaluation of the critical stress areas.
This may be accomplished by appropriate analytical means supplemented, when
necessary, by strain sensitive coatings or photoelastic methods. The distribution and
number of strain gauges should cover the load spectrum adequately for each part
essential to the safe operation of the rotorcraft as identified in § 27.573(d)(1). Other
devices such as accelerometers may be used as appropriate.
(2) The corresponding flight parameters (airspeed, rotor RPM, center-of-gravity
accelerations, etc.) should also be recorded simultaneously by appropriate methods.
This is necessary to correlate the loads and stresses with the maneuver or operating
conditions at which they occurred.
(3) The instrumentation system should be adequately calibrated and checked
periodically throughout the flight strain measurement program to ensure consistent and
accurate results.
(C) Parts to be Strain-Gauged. Fatigue critical portions of the rotor systems,
control systems, landing gear, fuselage, and supporting structure for rotors,
transmissions, and engine are to be strain-gauged. For rotorcraft of unusual or unique
design, special consideration might be necessary to ensure that all the essential parts
are evaluated.
(D) Flight Regimes and Conditions to be investigated.
(1) Typical flight and ground conditions to be investigated in the flight strain
measurement program are given in paragraphs c. and d. of AC 27-1B, MG 11.
(2) The determination of flight conditions to be investigated in the flight strain
measurement program should be based on the anticipated use of the rotorcraft and, if
available, on past service records for similar designs. In any event, the flight conditions
considered appropriate for the design and application should be representative of the
actual operation in accordance with the rotorcraft flight manual. In the case of
multiengine rotorcraft, the flight conditions concerning partial engine-out operation
should be considered in addition to complete power-off operation. The flight conditions
to be investigated should be submitted in connection with the flight evaluation program.
Page C - 116
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.