FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-115

PDF page 265 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 265
AC 27-1B · C-115Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

12/1/2011                                       AC 27-1B, Chg 4


should be taken to ensure that the internal loads and boundary conditions are valid.
The following should be considered:

            (i) strain gauge data on undamaged structure to establish points of high stress
concentration as well as the magnitude of the concentration;

             (ii) locations where analysis shows high stress or low margins of safety;

              (iii) locations where permanent deformation occurred in static tests;

          (iv) locations of potential fatigue damage identified by fatigue analysis;

         (v) locations where the stresses in adjacent elements will be at a maximum with
an element in the location failed;

                     (vi) partial fracture locations in an element where high stress
concentrations are present in the residual structure;

           (vii) locations where detection would be difficult; and

            (viii) design details that service experience of similarly designed components
indicates are prone to fatigue or other damage.

      (3) In addition, the areas of probable damage from sources such as a severe
corrosive or fretting environment, a wear or galling environment, or a high maintenance
environment should be determined from a review of the design and past service
experience.

   (C) The stresses and strains (steady and oscillatory) associated with all
representative steady and maneuvering operating conditions expected in service.

   (D) The frequency of occurrences of various flight conditions and the corresponding
spectrum of loadings and stresses.

   (E) The fatigue strength, fatigue crack propagation characteristics of the materials
used and of the structure, and the residual strength of the damaged structure.

   (F) Inspectability, inspection methods, and detectable flaw sizes.

  (G) Variability of the measured stresses of paragraph f.(6)(iv)(C), the actual flight
condition occurrences of paragraph f.(6)(iv)(D), and the fatigue strength material
properties of paragraph f.(6)(iv)(E).

   (v) Flight strain measurement program.



                                                         Page C - 115

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →