FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-112

PDF page 262 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 262
AC 27-1B · C-112Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     12/1/2011


The lower the residual strength of a structure after an accidental damage event, the
shorter the inspection interval should be. Considerations of both inspectability and
impact surveys (including probability of occurrence) for specific structure may be used
to isolate the most critical threats to consider in setting a maintenance inspection
interval. Knowledge of the residual strength for a given critical damage is also needed
for such an evaluation.  If it is known that the design is capable of handling large and
clearly detectable damage, while maintaining a residual strength well above limit load, a
less rigorous engineering approach may be applied in establishing the inspection
interval.

               (2) Slow Growth Evaluation. This method is applicable when the damage
grows in the test and the growth rate is shown to be slow, stable, and predictable, as
illustrated in Figure AC 27.573-4. An inspection program should be developed
consisting of the frequency, extent, and methods of inspection for inclusion in the
maintenance plan. Inspection intervals should be established so that the damage will
have a very high probability of detection between the time it becomes initially
inspectable and the time at which the extent of the damage reduces the residual static
strength to limit load (considered as ultimate), including the effects of environment. For
any damage size that reduces the load capability below ultimate, the component is
either repaired to restore ultimate load capability or replaced. Should functional
impairment (such as unacceptable loss of stiffness) occur before the damage becomes
otherwise critical, this should be accounted for in the development of the inspection
program.


                      Ultimate
                                                                           Slow Growth            L_
   Static Strength                      I______Arrested Growth_
                          Limit



                           Critical
                        Size                             _  _J-----------Arrested Growth  Damage Size
                                     _J   r·-·No Growth
                Threshold of            i                                     Slow Growth
                  Detectability _      ....    ., ......... .,.1 ....... ., .. .,, ..... ., .. ., ... ·,., .. ., ...... ., .. ., ...... .


                                                            Slow Growth       time
                                                               Inspection Interval Basis

 Figure AC 27.573-4. Illustration of Residual Strength and Damage Size Relationships
                         for Fail-Safe Substantiation.

               (3) Arrested Growth Evaluation. This method is applicable when the
damage grows, but the growth is mechanically arrested or terminated before becoming

Page C - 112

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →