FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-111

PDF page 261 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 261
AC 27-1B · C-111Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

12/1/2011                                       AC 27-1B, Chg 4


ultimate load capability. Evaluation of Zone 3 damage should have sufficiently high
residual strength and, if necessary, supplemental procedures should be established to
minimize the risk of catastrophic failure. Full-scale, component, or sub-component
testing should be accomplished using one or more specimens subjected to constant
amplitude or spectrum loading applied in a manner representative of flight load
conditions. The test loads should be increased by factors that account for environment
and fatigue strength scatter. The results of the testing can be used to manage the
structure in one or a combination of the three methods described subsequently.

               (1) No Growth Evaluation. This approach is appropriate for inspectable in-
service damage which does not grow in service (see Figure AC 27.573-3). Damage
growth should be substantiated using either method described in f.(6)(iii)(B)(2) or
f.(6)(iii)(B)(3). Structural details, elements, sub-components, and components of critical
structural areas, or full-scale structures, should be tested under repeated loads for
validating a no-growth approach to the damage tolerance requirements. The number of
cycles applied to validate a no-growth concept should be statistically significant, and
may be determined by load or life considerations or both. Residual strength testing or
evaluations should be performed after repeated load cycling demonstrating that the
residual strength of the structure is equal to or greater than limit load considered as
ultimate. Moreover, it should be shown that stiffness properties have not changed
beyond acceptable levels. Inspection intervals should be established, considering the
residual strength capability associated with the assumed damage. The intent of this is
to assure that structure is not exposed to an excessive period of time with static margins
less than ultimate, providing a lower safety level than in the typical slow growth
situation, as illustrated by the Figure AC 27.573-3. Once the damage is detected, the
component is either repaired to restore ultimate load capability or replaced.

                          Da mage init iation
  Residual strength                                  or occurrence
                                             Slow-growth approach *           ,,    t
    Ult imate loads
           ~
                                 No-growth approach **
     Limit loads

                                                      * Repair to Restore Ultimate St rength
                                                    ** No growth without repair is not acceptable


                                                                        Time
                                                                         ,_
                  Figure AC 27.573-3. Residual Strength vs. Time.




                                                         Page C - 111

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →