FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-110

PDF page 260 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 260
AC 27-1B · C-110Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     12/1/2011


        (A) Damage Tolerant Safe-Life Evaluation. This is a “No-Growth” method in
which the structure, with damage present, is able to withstand repeated loads of
variable magnitude without detectable damage growth for the life of the rotorcraft or
within a specified replacement time. This evaluation may be used to substantiate any
type of damage that will remain in-service for the life of the part.

No specific inspection requirements are generated from the test program in this method.
However, compliance with routine inspections for cracking, delaminations, and service
damage and other limitations prescribed in accordance with § 27.1529 are always
required. Compliance using full-scale, component, or sub-component fatigue testing
can be accomplished by either of the following methods:

            (1) S-N Method. This method is based on determining the point where
initiation of growth occurs for the damage present at critical locations in the structure.
AC 27-1B, AC 27 MG 11, provides guidance that may be appropriate for this method.
The method utilizes one or more full-scale, component, or sub-component test
specimens subjected to constant-amplitude or spectrum loading applied in a distribution
on the structure that is representative of critical flight conditions. Any indication of
growth of the imposed damage and defects, or structurally significant cracking,
disbonding, splintering, or delaminating of the composite, defines the fatigue initiation
characteristic of the structure in terms of applied load and cycles. Working S-N curves
are established from the mean curve using strength or cycle reductions or both to
account for fatigue scatter and environmental effects. Flight loads are compared to this
working curve, and if any intercepts occur, a cumulative damage calculation is
conducted to establish the component retirement time. Compliance with the ultimate
load requirements should be demonstrated at the completion of the fatigue test.

            (2) Life-Test Method. This method uses spectrum fatigue testing to verify the
absence of damage growth over a large number of cycles that are equivalent to a
lifetime of expected usage. The method uses one or more full-scale, component, or
sub-component test specimens subjected to spectrum fatigue loading applied in a
representative distribution of flight loads, including Ground-Air-Ground (GAG) loads.
Fatigue test loads should be increased by factors for environment and fatigue strength
scatter. The load may also be increased using an S-N curve approach to reduce the
duration of the test. Any significant growth of the imposed damage, or structurally
significant cracking, disbonding, splintering, or delamination of the composite during the
test constitutes failure to achieve the desired lifetime. However, the equivalent life
demonstrated at the time of inception of damage growth or cracking can be used as a
retirement time for the component. Compliance with the ultimate load requirements
should be demonstrated at the completion of the fatigue test.

        (B) Damage Tolerant Fail-Safe (Residual Strength with Detectable Damage)
Evaluation. This method establishes inspection intervals to ensure that the structure
remaining after a partial failure is able to withstand design limit loads without failure or
excessive structural deformations within a specified inspection interval.  If the damage is
detected in an inspection, the structure should be either replaced or repaired to restore


Page C - 110

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →