FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-109

PDF page 259 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 259
AC 27-1B · C-109Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

12/1/2011                                       AC 27-1B, Chg 4


strength (e.g., below Ultimate, but well above limit load capability to ensure safety
without detection for long periods of time).  If it is further determined that such impact
events usually occur with the knowledge of maintenance or aircraft service personnel,
then the alternate procedures may be added to the Instructions for Continued
Airworthiness. For example, advanced inspection methods, which can detect damage
from high-energy blunt impacts, may be used as alternate procedures to minimize the
risk of catastrophic failure for such Zone 3 damage.

              (iii) Means of compliance. For each PSE, inspections, replacement times, or
other procedures must be established as necessary to avoid catastrophic failure.
Compliance with the requirements of § 27.573(d) and (e) should be shown by one, or a
combination of, the methods described subsequently. Generally, replacement times are
established using Damage Tolerance Safe Life Evaluations and Inspection Intervals are
established using Fail Safe Evaluations. From current state-of-the-art rotorcraft
applications, it is widely accepted that composite materials have good flaw and damage
tolerance capabilities and therefore the supplemental procedures may only be rarely
necessary. Damage tolerance evaluations are best suited for composite structures,
particularly those with structural redundancy and inherent resistance to damage growth.
Damage resulting from anomalous or accidental events must be considered in the
damage tolerant evaluations. The damage tolerant evaluation for replacement times
and inspection intervals is to be used unless it is established that neither can be
achieved within the limitations of geometry, inspectability, or good design practice. In
that case, supplemental procedures must be established and submitted to the FAA for
approval. In any case, the FAA must approve the methodology used for compliance to
§ 27.573.The substantiation method(s) should be chosen so that the structure is
protected against catastrophic failure from each of the threats identified in paragraph
f.(6)(ii)(C) of this AC by a specific procedure (inspection, replacement time, or other
procedure). For example, a manufacturing-related void of a specific allowable size
could be substantiated by means of a replacement time method with no scheduled
inspection. An accidental impact in the same area could be substantiated by an
inspection method with no specific replacement time. The result could be one structure
with several different inspection requirements (location, method, and interval) and a
fixed replacement time as well. This combination of procedures assures that each
threat is covered.The fatigue substantiation should include sufficient coupon, element,
sub-element, or component tests to establish the fatigue scatter, curve shapes, and the
environmental effects. The substantiation should include full-scale, component, or sub­
component fatigue testing but also may be accomplished by analysis supported by test
evidence. When spectrum testing is used, the lowest load levels can be eliminated from
the spectrum if they can be shown to be non-damaging. The substantiation should
include a static strength evaluation to show that the required residual strength and
adequate stiffness, accounting for the effects of environment, are retained for the life of
the structure or the appropriate inspection interval. Damage as determined in
paragraph f.(6)(ii) of this AC for the specific structure being substantiated should be
imposed at each critical area of the structure.



                                                         Page C - 109

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →