FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-108

PDF page 258 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 258
AC 27-1B · C-108Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     12/1/2011


(depicted in Figure AC 27.573-2) are dependent on the part of the structure under
evaluation and a threat assessment.

               (2) Obvious impact damage is used to define the threshold from which
damage is readily detectable and appropriate actions may be taken before the next
flight.

               (3) Barely Detectable Impact Damage (BDID) is the state of damage at the
threshold of detectability for the approved inspection procedure. Barely Visible Impact
Damage (BVID) is that threshold of visually detectable damage associated with a
detailed visual inspection procedure.

               (4) Detectable Damage is the state of damage that can be reliably
detected at scheduled inspection intervals. Visible Impact Damage (VID) is that
threshold associated with the type of damage that should be detectable during a
detailed visual inspection.

               (5) Three Zones are depicted by this figure:

             Zone 1: Since the damage is not detectable, Ultimate Load capability is
required. The provisions of paragraph f.(5) provide a means of compliance.

             Zone 2: Since the damage can be detected at a scheduled inspection,
Limit Load (considered as Ultimate load) capability is the minimum requirement for this
damage.

             Zone 3: Since the damage is not detectable with the proposed in-
service inspection procedures, ultimate load capability is required, unless an alternate
procedure can show an equivalent level of safety. For example, residual strength lower
than ultimate may be used in association with improved inspection procedures or with a
probabilistic approach showing that the occurrence of energy levels is low enough so
that an acceptable level of safety can be achieved.

Of the three zones, only Zone 3 may have a residual strength requirement that can vary
with alternate procedures or the probability of damage occurrence or both. In either
case, any compromise for residual strength requirements less than the ultimate load
requirement should only be considered when pursuing one of the options under the
damage tolerant fail-safe means of compliance, as described in the following section,
f.(6)(iii)(B).

One example of the use of alternate procedures is for the rare damage threat from a
high energy, blunt impact (e.g., service vehicle collision). Depending on the selected
maintenance inspection scheme, such damage may fall under Zone 3. When
considering such damage in the design of a part, it may be shown to be damage
tolerant fail safe, even though the damage is not detectable, based on a very low
probability of occurrence. As a result, the design may have sufficiently high residual


Page C - 108

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →