FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-106

PDF page 256 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 256
AC 27-1B · C-106Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     12/1/2011


of impact tests performed with configured structure, which is subjected to boundary
conditions characteristic of the structure. Many different impact scenarios and locations
are typically considered in the survey, which has a goal of identifying the most critical
impacts (i.e., those causing the most serious damage but are least detectable). When
simulating accidental impact damage, blunt or sharp impactors should be selected to
represent the maximum criticality versus detectability, according to the load conditions
(e.g., tension, compression or shear). Until sufficient service experience exists to make
good engineering judgments on energy and impactor variables, impact surveys should
consider a wide range of conceivable impacts, including runway or ground debris, hail,
tool drops, and vehicle collisions. Service data collected over time, can better define
impact surveys and design criteria for subsequent products, as well as establish more
rational inspection intervals and maintenance practice. Refer to paragraph f.(6)(ii)(H)
for various combinations of detectability and energy levels to be considered in the
damage tolerance and fatigue evaluation.

               (3) Discrete Source Damage. The structure should be able to withstand
limit static loads (considered as ultimate loads) and fatigue loads, which are reasonably
expected during a completion of a flight on which damage resulting from obvious
discrete source occurs (e.g., hail damage, bird strike, uncontained engine failure, and
uncontained high energy rotating machinery failure). The extent of damage should be
based on a rational assessment of service mission and potential damage relating to
each discrete source.

          (D) The use of composite secondary bonding in manufacturing or
maintenance requires strict process and quality controls to achieve the reliability needed
to use such technology in critical structures (see AC 21-26). Assuming good process
and quality controls, service history has shown that additional damage tolerant design
considerations are also needed to ensure the safety of structure with secondary bonds
(i.e., random, but an unacceptable number of weak bonds discovered in service).
Unless the ultimate strength of each critical bonded joint can be reliably substantiated in
production by NDI techniques (or other equivalent, approved techniques), then the limit
load capability should be ensured by any or a combination of the following:

               (1) Consider isolated disbonds and weak bonds (represented by zero
bond strength) in structural elements that use secondary bonding for primary load
transfer. The associated disbond size should be up to the limitations provided by
redundant design features (i.e., mechanical fasteners or a separate bonding detail).
The structure containing such damage should be shown to carry limit load by tests,
analyses, or some combination of both. For purposes of test or analysis demonstration,
each disbond should be considered separately as a random occurrence (i.e., it is not
necessary to demonstrate residual strength with all structural elements disbonded
simultaneously).

         (2) Each critical bonded joint on each production article should be proof-tested
to the critical limit load.



Page C - 106

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →