FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-104

PDF page 254 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 254
AC 27-1B · C-104Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     12/1/2011


standards that allow the static strength capability to degrade below the ultimate strength
capability assuming such damage occurs within the operational life of the structure.
However, when this damage occurs, the remaining structure must withstand expected
loads without failure or excessive structural deformations until the damage is detected
and the component is either repaired to restore ultimate strength capability or retired.

             (ii) General. The nature and extent of the required analysis or tests on
complete structures and portions of the primary structure can be based on applicable
previous fatigue or damage tolerant designs, construction, tests, and service experience
on similar structures. In the absence of experience with similar designs,
FAA/AUTHORITY approved structural development tests of components,
subcomponents, and elements should be performed. The following considerations are
unique to the use of composite material systems and should be observed for the
method of substantiation selected by the applicant. Rotorcraft structure provides a
broad range of composite applications that are quite different in terms of functionality,
geometry and inspectability. These include the rotors, the drive shafts, the fuselage,
control system components (e.g., push-pull rods), and the control surfaces. When
selecting the approach, attention should be given to the composite application under
evaluation, the type of potential damage and degradation of the structural design
details, the materials used and margin over flight loads. Whatever the approach
selected, the following considerations will apply for tests and analysis:

           (A) The test articles should be fabricated and assembled in accordance with
production specifications and processes so that the test articles are representative of
production structure.

           (B) The test articles should include material imperfections whose extent is
not less than the limits established under the inspection and acceptance criteria used
during the manufacturing process and consistent with the inspection techniques used in
service (e.g., visual, ultrasonic, X-ray). The initial extent of these imperfections should
be discussed and agreed with the FAA, taking into account experience in manufacturing
and routine in-service inspections. Typical defects to be considered include but are not
limited to the following:

               (1) Disbonds and weak bonds (considered as disbonds).

               (2) Delaminations, fiber waviness, porosity, voids.

               (3) Scratches, gouges, and penetrations.

               (4) Impact damage.

All of the damages identified in the preceding paragraph (B) above should be derived
from the threat assessment described in the following paragraph (C).
     (C) For each PSE, a threat assessment must be made of the probable locations,
types, and sizes of damage considering fatigue, environmental effects, intrinsic and


Page C - 104

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →