FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-103

PDF page 253 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 253
AC 27-1B · C-103Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

12/1/2011                                       AC 27-1B, Chg 4


              (iii) Allowables should be evaluated and used as specified in § 27.613. These
allowables may be generated at the lamina, laminate, or specific design feature level
(e.g., filled hole, lap joint, stringer run-out), provided they accurately reflect the actual
value and variability of the structural strength for the critical failure modes being
considered, at each point design where margins need to be established.

          (iv) The static test articles should be fabricated and assembled in accordance
with production specifications and processes so that they are representative of
production structure including defects consistent with the limits established by
manufacturing acceptance criteria.

         (v) The material and processing variability of the composite structure should be
considered in the static strength substantiation. This can be achieved by establishing
sufficient process and quality controls to manufacture structure and reliably substantiate
the required strength in tests and analyses, which support a building block approach.  If
sufficient process and quality controls cannot be achieved, it may be necessary to
account for greater variability with special factors (§ 27.619) applied to the design.
Such factors should be accounted for in the component static tests or analysis.

          (vi) It should be shown that impact damage (or other minor discrete source
damage) that can be realistically expected from manufacturing and service, but not
more than the established threshold of detectability for the selected inspection
procedure, will not reduce the structural strength below ultimate load capability. This
static strength capability can be shown by analysis supported by test evidence, or by a
combination of tests at the coupon, element, subcomponent, and component levels.
Later discussions in this AC address the issues associated with damage in excess of
that considered in f.(5) and drops in residual strength below ultimate load capability (see
paragraph f.(6) below).

      (6) The sixth area is the damage tolerance and fatigue evaluation requirements of
§ 27.573.

            (i) Background. The static strength determination required by §§ 27.305 and
27.307 establishes the ultimate load capability for composite structures that are
manufactured, operated, and maintained with established procedures and conditions.
The damage tolerance and fatigue evaluation required by § 27.573 mandates
procedures that allow the composite structure to retain the intended ultimate load
capability when subjected to expected fatigue loads and conditions during its
operational life. The requirements established for the damage tolerance and fatigue
evaluation include component replacement times, inspection intervals, or other
procedures as necessary to avoid catastrophic failure. These evaluations assume that
the baseline ultimate strength capability might be compromised by damage caused by
fatigue, environmental effects, intrinsic or discrete flaws, or accidental damage. This
damage includes flaws or defects, which may occur in manufacturing or maintenance
and which are used to set the ultimate strength capability and establish the
manufacturing acceptance criteria. The damage tolerance assessment establishes


                                                         Page C - 103

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →