Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
12/1/2011 AC 27-1B, Chg 4
evaluating a composite structure. These transitional load transfer areas typically
produce the highest stresses (and strains) and serve as the initiation sites for many of
the failures (including those due to the relatively low interlaminar strength of
composites) that occur in service in a full-scale part or assembly. Small scale tests
(such as coupon, element, and subcomponent tests), or equivalent approved testing
programs, and analytical techniques should be carefully designed, prepared, and
approved to evaluate potential “hot spots” and provide accurate simulations and
representations of full-scale article stresses and strains in the critical transition areas.
Proper certification work in this area will ensure initial safety and continued
airworthiness in full-scale production articles.
(vi) The design strain level for each major component and material system
should be established so that specified impact damage considerations are defined and
properly limited. The effects of the strain levels may be established for each composite
material using small-scale characterization tests and the results should be used to
establish or verify the maximum allowable design strain level for each full-scale article.
The maximum allowable design strain values selected should also take into account the
reliability and confidence levels established for the relevant portions of the quality
control system. This methodology is necessary because the amount and size of flaws
in the production article may restrict the allowable level of design strain. In a
no-flaw-growth design, the maximum specified impact damage and manufacturing flaw
size at the most critical location on the part will be a major factor in determining the
maximum allowable elastic strain. This design approach is currently selected for nearly
all civil and most military applications; since, under normal conditions, only visual
inspections are required in the field (unless unusual external damage circumstances
such as a hail storm occur) to maintain the initial level of airworthiness (safety).
However, many military applications, because of their demanding missions, employ
scheduled field non-destructive inspection (NDI) maintenance, (such as comparative
ultrasonics) to ensure that flaw growth either does not occur, is controlled by approved
structural repair, or by replacement of affected parts. To date, civil applicants have not
requested a flaw growth, phased NDI approach. Therefore, selection of the full-scale
article’s design strain limit based on small-scale tests for a no flaw growth design is
extremely important.
(vii) Composite and adhesive properties should be determined so that
detrimental structural creep does not occur under the sustained loads and environments
expected in service. Small-scale characterization tests (such as coupon, element, and
subcomponent tests) and analysis, which verify and establish the full-scale design
criteria and parameters necessary to ensure that detrimental structural creep in
full-scale structure does not occur in service, should be conducted early in certification
and should be FAA-approved.
(viii) Material allowable strength values for full-scale design and testing should
be developed using the coupon procedures presented in CMH-17 or equivalent. The
intent is to represent the material variability including the effects that can occur in
multiple batches of material and process runs. At least three batches of material
Page C - 99
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.