FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-98

PDF page 248 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 248
AC 27-1B · C-98Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     12/1/2011


the case of composites, determination of these basic constituent and material system
properties will almost invariably involve the submittal, acceptance, and use of company
standards. This is currently necessary because the FAA (new managers of CMH-17)
has not completed development of “B” basis allowables for inclusion in CMH-17. Also,
test methods vary somewhat from manufacturer to manufacturer; therefore, individual
company results will exhibit some scatter in final material property values. Any
company standard that is used should meet or exceed related CMH-17 requirements.
Material structural acceptance criteria and property determination should, as a
minimum, include the following:

            (i) Property characterization requirements of all material systems (e.g.,
pre-pregs, adhesives) and constituents (e.g., fibers, resins) should be identified,
documented, and approved. These requirements, once approved, should be placed in
all appropriate procedures and specifications such as those in paragraph f.(1).

             (ii) Moisture conditioning of test coupons, parts, subassemblies, or assemblies
should be accomplished in accordance with CMH-17, other similar approved methods
or per FAA approved programs.

              (iii) The maximum and minimum temperatures expected in service (as derived
from test measurements, thermal analyses on panels and other parts, experience, or a
combination) should be determined and accounted for in static and fatigue strength
(including damage tolerance) substantiation programs considering associated humidity-
induced effects.

          (iv) The wet glass transition temperature, Tg, is an important characteristic
parameter of amorphous polymers, such as epoxies.  It is the temperature below which
the polymer behaves like a “glassy” solid and above which it behaves like a “rubbery”
solid (i.e., it is the temperature at which there is a very rapid change in physical
properties). The change from a hard polymeric material to a rubbery material takes
place over a narrow temperature range. A composite material will experience a drastic
reduction in matrix-controlled mechanical material properties when loaded in this
temperature range. Since the resin is the critical structural element in a composite
matrix and the Tg is critical to structural integrity, a Tg determination is necessary. The
Tg margin methodology of CMH-17 should be implemented (i.e., the Tg should be 50° F
higher than the maximum structural temperature (see definition)). For any type of resin
or adhesive, an acceptable temperature margin using CMH-17 techniques (e.g.,
consideration of limited high temperature excursions) or equivalent methodologies
based on tests or experience, or both, should be established and approved early in the
certification process.

         (v) Local design values should be established by analysis and characterization
tests and approved for specific structural configurations (point designs), which include
the effects of stress risers (e.g., holes, notches) and structural discontinuities (e.g.,
joints, splices). Proper determination of these values for full-scale design and test
should be considered one of the most critical building blocks in substantiating and


Page C - 98

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →