FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-96

PDF page 246 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 246
AC 27-1B · C-96Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                     12/1/2011


   (1) The first area is the fabrication requirements of § 27.605:

        (i) The quality control system should be developed considering the critical
engineering, manufacturing, and quality requirements and a guidance standard such as
AC 21-26, “Quality Control for the Manufacture of Composite Materials." This ensures
that all special engineering, or manufacturing quality instructions for composites are
presented, evaluated, documented, and approved, using drawings, process and
manufacturing specifications, standards, or other equivalent means. This should be one
of the early phases of a composite structure certification program, since this represents
a major building block for sequential substantiation work. Some important concepts of
AC 21-26 are included below.

         (ii) Specific allowable defect limits (e.g., fiber waviness, warp defects, fill defects,
porosity, hole edge effects, edge defects, resin content, large area disbonds, and
delaminations) for a particular material system component, laminate design, detailed
part, or assembly should be jointly established by engineering, manufacturing, and
quality, and the associated inspection programs created, validated, and approved for
defect detection. Each critical engineering design should consider the variability of the
manufacturing process to determine the worst case effects (maximum waviness,
disbonds, delaminations, and other critical defects) allowed by the reliability limitations
of the approved inspection program.

         (iii) If bonds or bond lines such as those typical of rotorcraft rotor blade structure
are used, special inspection methods, special fabrication methods, or other approved
verification methods (e.g., engineering proof tests - see paragraph f.(6)) should be
provided to detect and limit disbonds or understrength bonds.

       (iv) Structurally critical composite construction fabrication process and
procurement specifications, for fabricating reproducible and reliable structure, must be
provided and FAA approved early during the certification process and should, as a
minimum, cover the following:

         (A) Vendor and Qualified Parts List (QPL) Control. Applicants should be able
to demonstrate to FAA certification team members (both the manufacturing inspection
district office (MIDO) and FAA engineering) at any time, that their quality control
systems ensure on a continuous basis, that only qualified suppliers provide the basic
material constituents or material systems (e.g., pre-pregs) that meet approved material
specifications. Recommended guidelines for qualification of alternate material systems
and suppliers are contained in CMH-17. These methods can also be used periodically
for qualification status renewals of existing material systems and suppliers.

     (B) Receiving Inspection and In-Process Inspection. Applicants should be able to
demonstrate to FAA certification team members (both MIDO and engineering), at any
time, that their receiving and in-process quality control systems provide products, which
continuously meet approved material and process specifications. Quality systems


Page C - 96

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →