FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-93

PDF page 243 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 243
AC 27-1B · C-93Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

12/1/2011                                       AC 27-1B, Chg 4


provides damage tolerance of the maximum defects allowed during the certification
process using the approved design fatigue spectrum.

     (37) Material System. The combination of single constituents chosen (e.g., fiber
and resin).

     (38) Material System Constituent. A single constituent (ingredient) chosen for a
material system (e.g., a fiber, a resin).

     (39) Matrix. The essentially homogeneous material in which the fibers or filaments
of a composite are embedded in resins, which are mainly thermoset polymers in aircraft
structure.

     (40) Maximum Structural Temperature. The temperature of a part, panel or
structural element due to service parameters such as incident heat fluxes, temperature,
and air flow at the time of occurrence of any critical load case, (i.e., each critical load
case has an associated maximum structural temperature). This term is synonymous
with the term “maximum panel temperature.”

     (41) Multiple Load Path. Structure providing two or more separate and distinct
paths of structure that will carry limit load after complete failure of one of the members.

     (42) Passive Multiple Load Path. Structure providing load paths with one or more
of the members (or areas of a member) relatively unloaded until failure of the other
member or members.

     (43) Point Design. An element or detail of a specific design, which is not
considered generically applicable to other structure for the purpose of substantiation
(e.g., lugs and major joints). Such a design element or detail can be qualified by test or
by a combination of test and analysis.

     (44) Porosity. A condition of trapped pockets of air, gas, or void within a solid
material, usually expressed as a percentage of the total nonsolid volume to the total
volume (solid + nonsolid) of a unit quantity of material.

     (45) Pre-Preg, Preimpregnated. A combination of mat, fabric, nonwoven material,
tape, or roving already impregnated with resin, usually partially cured, and ready for
manufacturing use in a final product that will involve complete curing. Pre-preg is
usually drapable, tacky, and can be easily handled.

     (46) Principal Structural Element (PSE). A structural element that contributes
significantly to the carrying of flight or ground loads and whose failure can lead to
catastrophic failure of the rotorcraft.
     (47) Residual Strength. The strength retained for some period of unrepaired use
after a failure or partial failure due to fatigue, accidental, or discrete source of damage.



                                                          Page C - 93

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →