FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-91

PDF page 241 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 241
AC 27-1B · C-91Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

12/1/2011                                       AC 27-1B, Chg 4


     (11) Cocure. The process of curing several different materials in a single step.
Examples include the curing of various compatible resin system pre-pregs, using the
same cure cycle, to produce hybrid composite structure or the curing of compatible
composite materials and structural adhesives, using the same cure cycle, to produce
sandwich structure or skins with integrally molded fittings.

     (12) Component. A major section of the airframe structure (e.g., wing, fin, body,
horizontal stabilizer), which can be tested as a complete unit to qualify the structure.

     (13) Coupon. A small test specimen (e.g., usually a flat laminate) for evaluation of
basic lamina or laminate properties or properties of generic structural features (e.g.,
bonded or mechanically fastened joints).

     (14) Cure. To change the properties of a thermosetting resin irreversibly by
chemical reaction (i.e., condensation, ring closure, or addition). Cure may be
accomplished by addition of curing (crosslinking) agents, with or without a catalyst, and
with or without heat.

     (15) Damage. A generic term for structural anomalies caused by manufacturing
(processing, fabrication, assembly or handling) or service usage. Trimming, fastener
installation, or foreign object impact are potential sources of damage, along with fatigue
and environmental effects.

     (16) Damage Tolerance. The attribute of the structure that permits it to retain its
required residual strength for a period of use after the structure has sustained a given
level of fatigue, corrosion, accidental or discrete source damage.

     (17) Damage Tolerant Fail-Safe. The capability of structure remaining after a
partial failure to withstand design limit loads without catastrophic failure within an
inspection period.

     (18) Damage Tolerant Safe Life. Capability of structure with damage present to
survive expected repeated loads of variable magnitude without detectable damage
growth and to maintain ultimate load capability throughout service life of the rotorcraft.

     (19) Delamination. The separation of the layers of material in a laminate.

     (20) Design Limit Loads. The maximum loads to be expected in service, as
defined by § 27.301(a).

     (21) Detail. A non-generic structural element of a more complex structural
member (e.g., specific design configured joints, splices, stringers, stringer runouts, or
major access holes).




                                                          Page C - 91

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →