Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 3 9/30/2008
service life obtained from standard configuration flight loads data and loading spectrum,
or from external cargo configuration flight loads data and loading spectrum or from
frequent ground-air-ground cycles is generally the approved service life or replacement
time. Since the regulatory maintenance and operating rules do not require recording
time in service for the different types of operations, this procedure could be used if an
“operational cycles” equation for equivalent flight hours is not approved (see (8) below).
(8) The Airworthiness Limitations Section of the maintenance manual shall
contain the required information derived from complying with the standard. If an
“operational cycles” equation for “equivalent flight hours” is approved under the
standard, the equation is included in this approved section of the manual.
(9) The applicant should plan to conduct a flight loads survey program for both
a standard configuration and an external cargo configuration, if applicable. The
ground-air-ground cycle is inherent in these conditions. This procedure will avoid
delays associated with reinstallation and calibration of equipment.
AC 27.571A. §27.571 (Amendment 27-33) FATIGUE EVALUATION OF FLIGHT
STRUCTURE FOR CATEGORY A CERTIFICATION.
a. Explanation. Amendment 27-33 added Appendix C to specify the requirements
for Category A certification of normal category rotorcraft. The requirement for fatigue
tolerance evaluation will require test evidence to support the analysis.
b. Procedures. For Category A certification, the tests specified in
paragraph AC 29.571A are required for fatigue tolerance evaluation.
Paragraph AC 29.571A is repeated in this section.
(1) Fatigue test evidence is necessary for the fatigue evaluation of gears. The
test evidence should be provided by rotating tests of complete gearbox specimens
operating under power. The tests provide the basis for analysis leading to the
establishment of safe life.
(2) The tests are conducted specifically for the purpose of gear tooth
evaluation, and components subjected to the tests do not have to be considered
serviceable on completion of the test. Excessive wear on bearings and shafts and
marking (including spalling) of bearings and gear teeth are acceptable provided no
fatigue damage is evident on the gear teeth. However fatigue damage other than tooth
fatigue should be considered for test validity and the integrity of the affected part
confirmed as necessary.
(3) The test conditions (torque versus number of cycles) should permit the
setting of mean strength curve(s) to be associated with each primary gear in the drive
train. The test conditions, should at a minimum, encompass those power levels for
which repeated application inservice is expected under normal circumstances. The S-N
curve(s), for the material and type of gear, should be reduced by a factor of safety to
Page C - 86
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.