Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/2008 AC 27-1B, Chg 3
(5) The difference in loading spectrum for different models that may be
anticipated is illustrated by comparing the percentage of time assigned to level flight
conditions, specifically 0.8 VH to 1.0 VH for three different rotorcraft designs as shown in
figure AC 27.571-1. (VH is the maximum airspeed at maximum continuous power in
level flight.) The first column applies to a single-piston-engine powered small rotorcraft
used in utility operations. The second column is appropriate for a single-turbine-engine
powered seven-place small business and utility rotorcraft. The third column is
appropriate for a twin-engine-powered 13 passenger transport rotorcraft. It should be
noted that the level flight percentage of occurrences shown in figure AC 27.571-1 for the
turbine utility business and turbine transport rotorcraft are examples of particular
designs. The high percentage of time shown in this level flight regime could be
unconservative for some designs, especially if the stresses under these design
conditions produce an infinite fatigue life for the particular component. The fatigue
spectrum percentage of occurrences should be modified according to the intended
operation usage of the rotorcraft. However, a conservative application should be
considered. This variation illustrates the “tailoring” of the loading spectrum for the type
of rotorcraft and the anticipated usage.
FIGURE AC 27.571-1
Comparison Percent of Time in Level Flight
Turbine
Piston Utility Twin Turbine
Utility Business Transport
0.8 VNE 25% 0.8 VH 16% 0.8 VH 15%
1.0 VH 15% 0.9 VH 21% 0.9 VH 20%
1.0 VNE 3% 1.0 VH 24% 1.0 VH 38%
Total 43% 61% 73%
(6) External cargo operations are a unique and demanding operation. A
“logging” operator may use 50 maximum power applications per flight hour to move logs
from a cutting site to a hauling site. Power is used to accelerate, decelerate, or hover
prior to load release. Lifting loads over an obstruction or natural barrier is another
example of very frequent high power applications for takeoff and for hovering over the
release area. Similar types of operations require flight loads data to assess the effects
on fatigue critical components.
(7) The impact of the external cargo operation on standard configuration limits
should be assessed to determine whether or not the component service lives,
inspections, etc., will be affected. The assessment may be done by calculating an
“external cargo configuration” service life for each critical component. The lowest
Page C - 85
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.