FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-84

PDF page 234 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 234
AC 27-1B · C-84Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 3                                                       9/30/2008

               (iv)   Fatigue strength, and/or fatigue crack propagation characteristics,
residual strength of the cracked structure.

         (2) Since the design limits, e.g., rotor RPM (maximum and minimum), airspeed,
and blade angles (thrust, weight, etc.) affect the fatigue life of the rotor system, it is
necessary that flight conditions be conducted at limits that are appropriate for the
particular rotorcraft and at the correct combination of these limits.  It will be the
responsibility of engineering and flight test personnel to determine that the flight strain
program proposal includes conditions of flight at the various combinations of rotor RPM,
airspeed, thrust, etc., that will be representative of the limits used in service. The flight
test personnel should assure that the severity of the maneuvers to be investigated is
such that actual service use will not be more severe. Verification that proposed
maneuvers are suitable may be achieved by:

                  (i)    Flying a representative set of maneuvers with the applicant’s pilot in
the test aircraft at noncritical combinations of weight, CG, and speed. (An
FAA/AUTHORITY letter for specific test authorization would ordinarily be required.)  If
the procedure is used, the applicant should provide adequate preliminary flight strain
data from development or other tests to confirm a cleared (non-critical) flight envelope
for conduct of these representative maneuvers.

                   (ii)   Flying a representative set of maneuvers with the applicant’s pilot in a
similar (certified) model to assess and agree upon the required maneuvers, control
deflections, and aircraft rates. The required maneuvers or conditions will be specified in
the flight strain program plan.

                    (iii)   Flying a chase aircraft which has a flight envelope appropriate to allow
visual confirmation of the proposed and programmed flight maneuvers.

               (iv)  Observation of telemetered flight data to assure desired control
deflections, rates, and aircraft attitudes.

              (v)  Some combinations of items b(2)(i) through b(2)(iv) above.

         (3) Assessing the operation spectrum and the flight loads or strain
         measurement program will involve airframe, propulsion, and flight test
           personnel.

         (4) Variation in the operating or loading spectrum among models, and
variations in the spectrum for a particular model rotorcraft, should be evaluated.
Figure AC 27 MG 11-7 contains typical flight load measurement program conditions to
be investigated. An example of a twin turbine spectrum is presented in Figure AC 27
MG 11-9. The tables should be used only as a guide and should be modified as
necessary for each particular rotorcraft design.




Page C - 84

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →