Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/2008 AC 27-1B, Chg 3
SUBPART C - STRENGTH REQUIREMENTS
FATIGUE EVALUATION
AC 27.571. § 27.571 (Amendment 27-26) FATIGUE EVALUATION OF FLIGHT
STRUCTURE.
a. Explanation. An evaluation is required to assure structural reliability of the
rotorcraft in flight. This evaluation may take the form of either tests or analysis. During
the certification process, fatigue testing is more effective than analysis alone in
identifying and preventing cracking that may occur during service. Analysis used for
substantiation should be validated by tests.
(1) Chapter 3 AC 27 MG 11 contains background information and acceptable
means of compliance with the requirements. A safe life may be assigned or the
structure may be fail safe as prescribed or a combination of these may be used.
(2) Mandatory inspections, service life (replacement times) etc., determined in
complying with the standard shall be placed in the Airworthiness Limitations Section of
the Instructions for Continued Airworthiness (also called Maintenance Manual). See
Appendix A of FAR Part 27, paragraphs A27.4 and paragraph AC 27.1529 for
information.
(3) Amendment 27-26 amended the standard to require evaluation of the
landing gear and their related primary attachments.
(4) Amendment 27-26 also amended the standard to require evaluation of
ground-air-ground cycles on the rotorcraft, and if applicable, of external cargo
operations. Previously external cargo operations were evaluated whenever the
rotorcraft cargo combination exceeded the “standard” maximum certificated gross
weight, and the CG range specified in § 27.25(c). If these limits were not exceeded, an
evaluation was not required by the standard prior to Amendment 27-26.
b. Procedures.
(1) The fatigue evaluation requires consideration of the following factors:
(i) Identification of the structure/components to be considered.
(ii) The stress during operating conditions.
(iii) The operating spectrum or frequency of occurrence including
frequency of ground-air-ground cycles, as well as external cargo operations.
Page C - 83
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.