Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
(1) The rotorcraft support structure, structure-float attachments, and floats
should be substantiated for rational limit and ultimate ditching loads.
(2) The most severe wave heights for which approval is desired are to be
considered. A minimum of Sea State 4 condition wave heights should be considered
(reference paragraph AC 27.801 (§ 27.801) for a description of Sea State 4 conditions).
(3) The landing structural design consideration should be based on water
impact with a rotor lift of not more than two-thirds of the maximum design weight acting
through the center of gravity under the following conditions:
(i) Forward velocities of 0 to 30 knots (or a reduced maximum forward
velocity if it can be demonstrated that a lower maximum velocity would not be exceeded
in a normal one-engine-out landing).
(ii) The rotorcraft pitch attitude that would reasonably be expected to
occur in service. Autorotation flight tests or one-engine-inoperative flight tests, as
applicable, should be used to confirm the attitude selected. This information should be
included in the Type Inspection Report.
(iii) Likely roll and yaw attitudes.
(iv) Vertical descent velocity of 5 FPS or greater.
(4) Landing load factors and water load distribution may be determined by
water drop tests or analysis based on tests.
(5) Auxiliary or emergency float loads should be determined by full immersion
or the use of restoring moments required to react upsetting moments caused by
sidewind, asymmetrical rotorcraft landing, water wave action, rotorcraft inertia, and
probable structure damage and punctures considered under § 27.801. Auxiliary or
emergency float loads may be determined by tests or analysis based on tests.
(6) Floats deployed after initial water contact are required to be substantiated
by tests or analysis for the specified immersion loads (same as for (5) above and for the
specified combined vertical and drag loads).
Page C - 82
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.