Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
AC 27.563 § 27.563 (Amendment 27-11) STRUCTURAL DITCHING PROVISIONS.
a. Explanation. Amendment 27-11 included certification requirements for ditching
approvals. The rotorcraft must be able to sustain an emergency landing in water as
prescribed by § 27.801(e).
b. Procedures. Refer to paragraph AC 27.801 for procedures.
AC 27.563A § 27.563(Amendment 27-26) STRUCTURAL DITCHING
PROVISIONS.
a. Explanation. Amendment 27-26 added specific structural conditions to be
considered to support the overall ditching requirements of § 27.801. These conditions
are to be applied to rotorcraft for which over-water operations and associated ditching
approvals are requested.
(1) The forward speed landing conditions are specified as:
(i) The rotorcraft should contact the most critical wave for probable water
conditions, in the likely pitch, roll, and yaw attitudes.
(ii) The forward velocity relative to wave surface should be in a range of 0
to 30 knots with a vertical descent rate of not less than 5 FPS relative to the mean water
surface.
NOTE: A forward velocity of less than 30 knots may be used for multiengine rotorcraft
if it can be demonstrated that the forward velocity selected would not be exceeded in a
normal one-engine-out touchdown.
(iii) Rotor lift of not more than two-thirds of the design maximum weight
may be used to act through the CG throughout the landing impact.
(2) For floats fixed or deployed before water contact, the auxiliary or emergency
float conditions are specified in § 27.563(b)(1). Loads for a fully immersed float should
be applied (unless it is shown that full immersion is unlikely). If full immersion is
unlikely, loads resulting from restoring moments are specified for sidewind and
unsymmetrical rotorcraft landing.
(3) Floats deployed after water contact are normally considered fully immersed
during and after full inflation. An exception would be when the inflation interval is long
enough that full immersion of the inflated floats does not occur; e.g., deceleration of the
rotorcraft during water impact and natural buoyancy of the hull prevent full immersion
loads on the fully inflated floats.
b. Procedures.
Page C - 81
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.