FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-76

PDF page 226 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 226
AC 27-1B · C-76Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 1                                                           2/12/03

              (F) Manufacturer, governing specification, serial number, and test weight
of ATD used in the tests, and a description of any modifications or repairs performed on
the ATD which could cause them to deviate from the specification.

            (G) A description of the photographic-instrumentation system used in the
tests (Paragraph c.(2)(iii)(B)).

                   (ii)   Seat/Restraint system data.

              (A) Manufacturers name and identifying model numbers of the
seat/restraint system used in the tests, with a brief description of the system, including
identification and a functional description of all major components and photographs or
drawings as applicable.

              (B) For unsymmetrical systems, an analysis supporting the selection of
most critical conditions used in the tests.

         (2) Test Proposal or Plan and Description. The description of the test should
be documented in enough detail so that the tests could be reproduced by following the
guidance given in the report. The procedures outlined in this guidance can be
referenced in the report but should be supplemented, as necessary, to describe the
unique conditions of the individual seat design.

                  (i)    Pertinent dimensions and other details of the installation not included
in the drawings of the test items should be provided. This can include footrests,
restraint system webbing guides and restraint anchorages, “interior surface”
simulations, bulkhead or sidewall attachments for seats or restraints, etc.

                   (ii)   The floor deformation procedure, guided by goals of most critical
loading for the test articles, should be documented.

                    (iii)  Placement and characteristics of electronic and photographic
instrumentation chosen for the test, beyond that information provided by the facility,
should be documented. This can include special targets, grids or marking used for
interpretation of photo documentation, and transducers and data channel characteristics
for lap belt loads, floor reaction forces, or other measurements beyond those discussed
in this guidance.

               (iv)  Any unusual or unique activity or event pertinent to conducting the test
should be documented. This could include use of special “breakaway” restraints or
support for the ATD’s, test items or transducers, operational conditions or activities such
as delayed or aborted test procedures, and failures of test fixtures, instrumentation
system components or ATD.

         (3) Test results report. The documentation should include copies of all test
results, analysis, and conclusions. As a minimum, the following should be documented:


Page C - 76

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →