FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-75

PDF page 225 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 225
AC 27-1B · C-75Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

               (2) Encroach into any required passageway to large exits.

               (3) Encroach more than 1.5 inches into any cross aisle or evacuation
(flight attendant) assist space for certain exits.

                   (ii)   Stowable Seats. Stowable seats, if used, should stow post-test and
remain stowed without projecting into any required passageways. In addition, they
should not project more than 1.5 inches into any flight attendant assist space or
cross-aisle.

              (A) Seats that are Stowed Manually. A post-test stowage force no greater
than 10 pounds (22kg) above the original stowage force may be used to stow the seat.

              (B) Seats that Stow Automatically. For a seat that may interfere with the
opening of any exit, it shall automatically retract to a position that does not interfere with
the exit opening as prescribed in § 27.807. For determining encroachment into
passageways, cross-aisles, and assist spaces, a posttest stowage force no greater than
10 pounds (22kg), applied at a single point, may be used to assist automatic retraction.

     e. Test Documentation.

         (1) General. The tests discussed in this guidance should be documented in
reports describing the test procedures and results. The test proposal, a description of
the required tests, approved by the FAA should be referenced in the test report and
contain the following:

                  (i)    Facility data.

              (A) The name and address of the test facility performing the tests.

              (B) The name and telephone number of the individual at the test facility
responsible for conducting the tests.

             (C) A brief description and/or photograph of each test fixture.

             (D) The date of the last instrumentation system calibration and the name
and telephone number of the person responsible for instrumentation system calibration.

              (E) A statement confirming that the data collection was done in
accordance with the recommendations in this guidance or a detailed description of the
actual calibration procedure used and technical analysis showing equivalence to the
recommendations of this AC ( Paragraph c.(2)(iii)(A)).





                                                          Page C - 75

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →