Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
usually indicated by an abrupt displacement of the belt into the ATD’s soft abdominal
insert which can be seen by careful observation of photo data from a camera located to
provide a close view of the belt as it passes over the ATD’s pelvis. This movement of
the belt is sometimes indicated in measurements of lap safety belt load (if such
measurements are made) by a transient decrease or plateau in the belt force, as the
belt slips over the prominence, followed by a gradual increase in belt force as the
abdominal insert is loaded by the belt. Retention of the lap safety belt can also be
verified by “submarining indicators” located on the ATD’s pelvis. These transducers are
essentially a series of small, uncalibrated load cells placed in or above the rim of the
ATD’s pelvis without changing its essential geometry. They indicate the position of the
lap safety belt by producing an electrical signal when they are under load from the belt.
(9) Femur load. Measuring femur loads is not required by the rotorcraft
standards. If a seat is installed in an aircraft in a manner that will expose the system to
loads from an occupant seated behind the seat system as well as the occupant seated
in the seat system, the tests discussed in this guidance should be conducted in a
manner to demonstrate that the system will perform properly under the combined
loading. For example, Test 2 should be conducted with at least two rows of seats in
place, as the seats in the first row carry the loads from the occupants in the first row, as
well as the leg kick loads from the second row (also noted in c.(3)(ii)(A) of this
guidance).
(10) Seat attachment. Documentation that the seat and restraint system has
remained attached at all points of attachment should be provided by still photographs
that show the intact system components in the load path between the attachment points
and the occupant.
(11) Seat deformation. Occupant seats evaluated in the tests discussed in this
guidance can deform permanently, either due to the action of discrete (impact) energy
absorber systems included in the design or due to residual plastic deformation of their
structural components. If this deformation is excessive, it could impede emergency
evacuation. Each seat design may differ in this regard and should be evaluated
according to its unique deformation characteristics. Permanent seat deformations are
measured on the critically loaded seat subsequent to conduct of the tests required in
§ 27.562. The seat deformation is measured subsequent to completion of the dynamic
tests and, where applicable, release of the applied pre-test floor deformation.
(i) Seats. The following post-test deformations and limitations regarding
emergency egress and access to exits may be used for showing compliance with
§ 27.785(j):
(A) Forward or Rearward Directions. The forward or rearward
deformations should not exceed a maximum of 4.0 inches (100 mm). In addition, the
clearance between undeformed seat rows, measured as shown in Figure AC 27.562-5
(Dimension A), should be a minimum of 9.0 inches, except where seat rows lead to
Type III or IV exits, where it should be a minimum of 11.0 inches. For seats with
Page C - 72
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.