FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-71

PDF page 221 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 221
AC 27-1B · C-71Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

over the ATD’s head or a head form during the test. Synthetic skins are discussed in
the Society of Automotive Engineers Information Report SAE J202, Synthetic Skins for
Automotive Testing.

         (4) Impact velocity. Impact velocity can be obtained by measurement of a time
interval and a corresponding sled displacement occurring just before or after (for
acceleration facilities) the test impact, and then dividing the displacement by the time
interval. When making such a computation, the possible errors of the time and
displacement measurements should be used to calculate a possible velocity
measurement error, and the test impact velocity should exceed the velocity shown in
Figure 27.562-1 by at least the velocity measurement error.  If the sled is changing
acceleration during the immediate pre-impact interval, or if the facility produces
significant rebound of the sled, the effective impact velocity can be determined by
integrating the plot of sled acceleration vs. time.  If this method is used, the sled
acceleration should be measured in accordance with Channel Class 180 requirements.

         (5) Upper torso restraint system load. The maximum load in the upper torso
restraint system webbing can be obtained directly from a plot or listing of webbing load
transducer output.  If a three-axis load transducer, fixed to the test fixture, is used to
obtain these data, the data from each axis should be combined to provide the resultant
vector magnitude.  If necessary, corrections should be made for the internal mass of the
transducer and the fixture weight it supports. This correction will usually be necessary
only when the inertial mass or fixture weight is high or when the correction becomes
critical to demonstrate that the measurements fall below the specified limits.

         (6) Compressive load between the pelvis and lumbar column. The maximum
compressive load between the pelvis and the lumbar column of the dummy can be
obtained directly from a plot or listing of the output of the load transducer at that
location. Since most load cells will indicate tension as well as compression, care should
be taken that the polarity of the data has been correctly identified.

         (7) Retention of upper torso restraint straps. Retention of the upper torso
restraint webbing straps on the ATD’s shoulders can be verified by observation of
photometry or documentary camera coverage. The webbing should remain on the
sloping portion of the ATD’s shoulder until the ATD rebounds after the test impact and
the upper torso restraint straps are no longer carrying any load. The webbing straps
should not bear on the neck or side of the head and should not slip to the upper
rounded portion of the upper arm during that time period.

         (8) Retention of lap safety belt. Retention of the lap safety belt on the
occupant’s (ATD) pelvis can be verified by observation of photometry or documentary
camera coverage. The lap safety belt should remain on the ATD’s pelvis, bearing on or
below each prominence representing the anterior superior iliac spines, until the ATD
rebounds after the test impact and the lap safety belt becomes slack.  If the lap safety
belt does not become slack throughout the test, the belt should maintain the proper
position throughout the test. Movement of the lap safety belt above the prominence is


                                                          Page C - 71

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →