FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-73

PDF page 223 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 223
AC 27-1B · C-73Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

deformations exceeding 4.0 inches, the undeformed clearances between seats should
be increased accordingly. In addition, at seat rows leading to Type III or IV exits, a
minimum of 20 inches clearance, measured above the arm rests, must be maintained
between adjacent seat rows. This measurement may be made with the seat backs
returned, using no more than original seat back breakover forces, to their pretest upright
or structurally deformed position. At other seat rows, the most forward surface of the
seat back should not deform to a distance greater than one half of the original distance
to the forwardmost hard structure on the seat (see Figure 27.562-6).

              (B) Downward Direction. There is no limitation on downward deformation,
provided it can be demonstrated that the feet or legs of occupants seated aft would not
be entrapped. Additionally, the seat bottom rotational deformation from the horizontal,
measured at the centerline of each seat pan, should not exceed 20° forward (pitch
down) or 35° aft (pitch up). This measurement should be made between the fore and
aft extremities of the seat pan structure, considering the final position of the seat pan
structure. In no case should rotation of the seat pan cause entrapment of the occupant.

             (C) Sideward Direction.

               (1) The deformed seat should not encroach more than 1.5 inches
(40 mm) into the required space for longitudinal aisle at heights up to 25 inches
(635 mm) above the floor. Determine which parts of the seat are at what heights prior
to testing.

               (2) The deformed seat should not encroach more than 2.0 inches
(50 mm) into the longitudinal aisle space at heights 25 inches (635 mm) or more above
the floor.

             (D) Additional Considerations. In addition, none of the above
deformations permit the seat to:

               (1) Affect the operation of any emergency exit or encroach into an
emergency exit opening for a distance from the exit not less than the width of the
narrowest passenger seat installed.





                                                          Page C - 73

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →