Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/12/03 AC 27-1B, Chg 1
d. Data Analysis And Compliance With The Criteria
(1) General. All data obtained in the dynamic tests should be reviewed for
errors. Baseline drift, “ringing,” and other common electronic instrumentation problems
should be detected and corrected before the tests. Loss of data during the test is
readily observed in a plot of the data vs. time and is typically indicated by sharp
discontinuities in the data, often exceeding the amplitude limits of the data collection
system. If these occur early in the test in essential data channels, the data should be
rejected and the test repeated. If they occur late in the test, after the maximum data in
each channel has been recorded, the validity of the data should be carefully evaluated,
but the maximum values of the data may still be acceptable for the tests described in
this guidance. The HIC does not represent a maximum data value, but represents an
integration of data over a varying time base. The head acceleration measurements
used for that computation should not be accepted if errors or loss of data are apparent
in the data at any time from the beginning of the test until the ATD and all test articles
are at rest after the test.
(2) Impact pulse shape. Data for evaluating the impact pulse shape are
obtained from an accelerometer that measures the acceleration in the direction parallel
to the line of inertial response shown in Figure 27.562-1 of this guidance. The impact
pulse intended for the tests discussed in this guidance has a symmetrical (isosceles)
triangular shape. Since this ideal pulse is considered a minimum test condition, it is
possible to evaluate the actual test pulse by comparing it with the ideal triangular pulse.
The ideal pulse can be drawn to scale on the data plot of the test sled or carriage
acceleration vs. time. The test pulse is acceptable if the plotted data are equal to or
greater than the ideal impact pulse. This method can lead to a practical necessity of
exceeding the ideal pulse by a significant degree, unless the test facility has precise
control in generating the test pulse. A graphic technique may be used to evaluate test
impact pulse shapes that are not precise isosceles triangles. A graphic technique is
contained in paragraph f. (1) of this guidance.
(3) Head Injury Criterion (HIC). Data for determining the HIC need to be
collected during the tests discussed in this guidance only if the ATD’s head is exposed
to secondary impact. The HIC is a method for defining an acceptable limit; i.e., the
maximum values of the HIC should not exceed 1,000 for head impact against broad
interior surfaces in a crash. The HIC is reported as the maximum value, and the time
interval during which the maximum value occurs is also given. Most facilities will make
this computation if requested. The HIC is calculated by computer-based data analysis
systems because manual attempts to use this method with real data are likely to be
tedious. The HIC is calculated according to the following equation:
Page C - 69
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.