Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
(B) Loads in restraint systems attaching directly to the test fixture can be
measured by three-axis load cells fixed to the test fixture at the appropriate location.
These commercially available load cells measure the forces in three orthogonal
directions simultaneously, so that the direction as well as the magnitude of the force can
be determined. If desired, similar load cells can be used to measure forces at other
boundaries between the test fixture and the test item, such as the forces transmitted by
the legs of the seat into the floor track. It is possible to use independent, single axis
load cells arranged to provide similar data, but care should be taken to use load cells
that can withstand significant cross-axis loading or bending without causing errors in the
test data, or use careful (often complex) installation to protect the load cells from
cross-axis loading or bending. Since load cells are sensitive to the inertial forces of
their own internal mass and to the mass of fixtures located between them and the test
article, as well as to forces applied by the test article, it may be necessary to
compensate the test data for that inaccuracy if the error is significant. Data for such
compensation will usually be obtained from an additional dynamic test replicating the
load cell installation but will not include the test item.
(v) Restraint system adjustment. The ATD should be sitting in the normal
upright position. Care should be taken not to tighten the restraint system beyond the
level reasonably expected in use and do not lock any emergency locking device (inertia
reel) prior to the impact. Automatic locking retractors should be allowed to perform the
webbing retraction and automatic locking function without assistance. Care should be
taken that emergency locking retractors sensitive to acceleration do not lock prior to the
impact test because of pre-impact acceleration applied by the test facility that is not
present in a landing impact. If “comfort zone” retractors are used, they should be
adjusted in accordance with instructions given to the user of the system. If manual
adjustment of the restraint system is required, it should be sufficient to remove slack in
the webbing, but it should not be adjusted so that it is unduly tight. Since the force
required to adjust the length of the webbing can be as high as 11 pounds, a preload of
12-15 pounds is commonly recommended. This load is too small to be accurately
measured by transducers selected to measure the high loads encountered in the impact
test, so it should be measured manually as the restraint is being adjusted. Special
gauges are commercially available to assist in this measurement. The preload should
be checked and adjusted, if necessary, just prior to the floor deformation phase of the
test.
(vi) Repetition of tests. It may be necessary to repeat the tests discussed
in this AC if accurate data are not collected in critical data channels or if some other
error occurs (e.g., cameras fail to operate, impact pulse inadequate, etc.). Preparation
for a repeated test should follow the same steps as for the initial test. The seat should
be removed from the fixture, and its attachment fittings or floor track examined and
replaced, if necessary, to correct any damage. The ATD should be carefully examined
and repaired or adjusted, if necessary. It is usually preferable to use a new seat and
restraint system for all repeated tests to preclude system failures due to undetected
damage. A new seat and restraint system should be used if there is any detectable
variation from the intended design configuration.
Page C - 68
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.