Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/12/03 AC 27-1B, Chg 1
(D) The ATD hands should be placed on the top of the legs, just behind
the knees. If tests on crew seats are conducted in a mockup with aircraft controls, the
ATD hands should be lightly tied to the controls. If only the seat and occupant restraint
system are tested, the ATD hands should be tied together with a lack cord that provides
about 24 inches of separation before the cord becomes tight. This will prevent
excessive arm flail during the ATD rebound phase.
(E) To the extent that they influence the injury criteria, all seat
adjustments and controls should be in the design position intended for the 50th
percentile male occupant. If seat and occupant restraint systems being tested are to be
used in applications where requirements (placards) dictate particular positions for
landing and takeoff, those positions should be used in the tests.
(F) The feet should be in the appropriate position for the type of seat
tested (flat on the floor for a passenger seat or on control pedals or on a 45° footrest for
flightcrew systems). The feet should be placed so that the centerlines of the lower legs
are approximately parallel, unless the need for placing the feet on aircraft controls
dictates otherwise.
(iv) Installation of instrumentation. Professional practice should be
followed when installing instrumentation. Care should be taken when installing the
transducers to prevent deformation of the transducer body from causing errors in data.
Lead-wires should be routed to avoid entanglement with the ATD or test item, and
sufficient slack should be provided to allow motion of the ATD or test item without
breaking the lead wires or disconnecting the transducer. Calibration procedures should
consider the effect of long transducer lead-wires. Head accelerometer (transducer)
should be installed in the ATD in accordance with the ATD specification and the
instructions of the transducer manufacturer. The load cell between the pelvis and the
lumbar spinal column should be installed as shown in Figure 27.562-4 of this guidance
or in a manner that would provide equivalent data.
(A) An upper torso restraint is required by § 27.785(b). The tension load
should be measured in a segment of webbing between the ATD’s shoulders and the
first contact of the webbing with hard structure (the anchorage point or a webbing
guide). Restraint webbing should not be cut to insert a load cell in series with the
webbing, since that would change the characteristics of the restraint system.
Commercially available load cells can be placed over the webbing without cutting. They
should be placed on free webbing and should not contact hard structure, seat
upholstery, or the ATD during the test. They should not be used on double-reeved
webbing, multiple-layered webbing, locally-stitched webbing, or folded webbing unless it
can be demonstrated that these conditions do not cause errors in the data. These load
cells should be calibrated using a length of webbing of the type used in the restraint
system. If the placement of the load cell on the webbing causes the restraint system to
sag, the weight of the load cell can be supported by light string or tape that will break
away during the test.
Page C - 67
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.