Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
restraint system, or the system may be used in several applications with different
interior configurations. In such cases, it will be necessary to document the head strike
path and the velocity along the path. This will require careful placement of photo
instrumentation cameras and location of targets on the ATD representing the ATD head
center of mass so that the necessary data can be obtained. These data can be used by
the interior designer to ensure that head impact with the interior will not take place or
that if possible head impact occurs, it will remain within the limits of the HIC. In the
event the head impacts the specific interior, the interior under evaluation should be
subjected to an individual special test to measure the head impact or HIC. The test is
done using a rigid 6.5-inch diameter spherical head form weighing 15 pounds, (which
includes necessary mass to represent the neck and a portion of the torso). The center
of the head form is guided along the previously determined head strike path so that the
form contacts the interior components at the velocity previously determined during the
seat and torso restraint system dynamic test. Accelerometers located at the center of
the head form would provide the data necessary for the HIC computation. If the interior
component to be impacted by the ATD has significant inertial response to the impact
environment, it will be necessary to evaluate those features or systems, such as
breakover seatbacks or instrument panels designed to move forward, relative to the
seat, in a dynamic test program which includes the full ATD occupant/seat/restraint
system. See b.(3)(ii) of this guidance for ATD and panel location for adjustable crew
seats.
(iii) Use of ATD. ATD used in the tests discussed in this guidance should
be maintained to perform in accordance with the requirements described in their
specification. Periodic teardown and inspection of the ATD should be accomplished to
identify and correct any worn or damaged components, and appropriate ATD calibration
tests (as described in their specification) should be accomplished if major components
are replaced. Each ATD should be clothed in form-fitting cotton stretch garments with
short sleeves, mid-calf length pants, and shoes (size 11E) weighing about 2.5 pounds.
The head and face of the ATD can be coated with chalk dust if it is desired to mark
head contact areas on seats or other structure. The friction in limb joints should be set
so that the joints barely restrain the weight of the limb when extended horizontally. The
ATD should be placed in the seat in a uniform manner for reproducible test results. For
the tests discussed in this guidance, the following procedures are adequate:
(A) The ATD should be placed in the center of the seat in as nearly a
symmetrical position as possible.
(B) The ATD’s back should be against the seat back without clearance.
This condition can be achieved if the ATD’s legs are lifted as it is lowered into the seat.
Then, the ATD is pushed back into the seat back as it is lowered the last few inches into
the seat pan. Once all lifting devices have been removed from the ATD, the ATD
should be “rocked” slightly to settle it in the seat.
(C) The ATD knees should be separated about 4 inches.
Page C - 66
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.