Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
extinguishers, survival equipment, etc.). If these items of mass are placed in a position
that could limit the function of an energy absorbing design concept in the test item, they
should be of representative shape and stiffness as well as weight. That is, seat stroking
should perform properly when used in rotorcraft interiors.
(ii) Consideration of test criteria. The test proposal or plan should be
planned to achieve “most critical” conditions for the criteria that make up each test.
(A) For multiple occupant seat assemblies, a rational structural analysis
should be used to determine the number and seat location for the ATD and the direction
for seat yaw in Test 2 to provide the most critical seat structural stress. This will usually
result in unequally loaded seat legs. The seat deformation procedure should be
selected to increase the load on the highest loaded seat leg and to stress the floor track
or fitting in the most severe manner. The seat position in Test 2 depends on the upper
torso restraint design. See c.(3)(ii)C below.
(B) If multiple row testing is used to gather data for HIC in passenger
seats, the seat pitch distance between seat rows should be selected within the
allowable range, so that the head would be most likely to contact hard structure in the
forward seat row. The effect of the 10° yaw in Test 2 and of any seat back breakover
should be considered. Results from previous tests or rational analysis can be used to
estimate the head strike path. Upper torso restraints may prevent head strike; however,
leg kick loads into the front seat row require use of two rows. This kick load is a seat
structural test not an ATD consideration.
(C) If nonsymmetrical upper torso restraints (such as single diagonal
shoulder belts) are used in a system, they should be installed on the test fixture in a
position representative of that in the aircraft and that would most likely allow the ATD to
move out of the restraint. For example, in a forward facing crew seat equipped with a
single diagonal shoulder belt, the seat should be yawed in Test 2 in a direction such that
the belt passes over the trailing shoulder. This is a part of the pass/fail criteria
evaluation.
(D) If a seat has sitting height adjustment, it should be tested in the
highest position that could be used by a 50th percentile male occupant in the aircraft
installation. See b.(3)(ii) of this guidance.
(E) Floor deformation need not be considered in assessing the
consequence of any seat deformation as related to the possible impairment of rapid
evacuation of the rotorcraft. After the test, the pitch and roll floor beams can be
returned to their neutral position and the necessary measurements of the seat
deformation made to determine the effect, if any, on rapid evacuation.
(F) In some cases, it may not be possible to measure data for HIC during
the test of the seat and torso restraint system. The design of the surrounding interior,
such as the instrument panel, may not be known to the designer of the seat and torso
Page C - 65
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.