Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
provisions and the actual procedure for accomplishment of the tests, are particular to
the test facility. These may be included in a test proposal or plan.
(i) Selection of test articles. Many seat designs compose a “family or
type” of seats which have the same basic structural design but differ in detail. For
example, a basic seat frame configuration can allow for several different seat leg
locations to permit installation in different rotorcraft. If these differences are of such a
nature that their effect can be determined by rational analysis, then the analysis can
determine the most highly stressed (“most critical”) configuration. The most highly
stressed configuration would normally be selected for the dynamic tests so that the
other configurations could be accepted by analysis and comparison with that
configuration. The HIC depends on head impact (secondary impact after rotorcraft
ground impact) and is more dependent on seat pitch for multiple row seats and on
location for others than on seat structural stress for a given “family” of seats, so that the
selection of the most highly stressed seat structure and the most critical seat pitch or
location will permit these factors to be evaluated in one dual row test under the
conditions of Test 2. Critical pelvic/lumbar spinal column forces are usually found under
the vertical impact conditions of Test 1 but are influenced by the upper torso restraint in
Test 2. Certain factors should be considered when employing that assumption. For
example:
(A) If the test item incorporates some energy absorbing or load limiting
design concept necessary to meet the test criteria or other requirement, a less severe
loading condition may adversely affect the performance of that design concept as
related to the pass-fail criteria. In such a case, it should be shown by rational analysis
or additional testing that the design concept would continue to perform as intended even
under the lower loads.
(B) If different configuration of the same basic design incorporated
load-carrying elements, especially joints or fasteners, which differed in detail design, the
performance of each detail design should be demonstrated in a dynamic test.
Experience has shown that small details in the design often cause problems in meeting
the test performance criteria.
(C) If structural strength is not the critical condition for achieving the
performance criteria of the dynamic test, the true critical condition should be evaluated
in a dynamic test. For example, if in one of the design configurations the restraint
system attachment points are located so that the lap safety belt was more likely to slip
above the ATD pelvis during the impact, then that configuration should also be
dynamically tested even though the structural loading might be less. In all cases, the
test item should be representative of the final production item in all structural elements
and should include seat cushions, armrests and armcaps, functioning position
adjustment mechanism, and correctly adjusted seat back breakover (if present), food
trays or any other service or accoutrements required by the seat manufacturer or
customer, and any other items of mass carried or positioned by the seat structure (e.g.,
weights simulating luggage carried or restrained by luggage restraint bars, fire
Page C - 64
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.