FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-63

PDF page 213 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 213
AC 27-1B · C-63Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                       AC 27-1B, Chg 1


cup to compensate for any weight lost because of this modification. The instrument
cavity plug (g) is cut to provide clearance for the adapter cup and added weight.

             (C) Other ATD modifications. Flailing of the ATD arms often causes the
“clavicle” used in the Part 572B ATD to break. To reduce the frequency of this failure,
the clavicle may be replaced by a component having the same shape but made of
higher strength material. This may increase the ATD weight slightly, but it would be
acceptable for the tests discussed in this guidance. Another useful modification is the
use of “submarining indicators” on the ATD pelvis. These electronic transducers are
located on the anterior surface of the ilium of the ATD pelvis without altering its contour
and indicate the position of the lap safety belt as it applies loads to the pelvis. Thus
they can provide a direct record that the lap safety belt remains on the pelvis during the
test and eliminates the need for careful review of high-speed camera images to make
that determination.

             (D) Equivalent ATD. The continuing development of ATD for dynamic
testing of seat restraint/crash-injury-protection systems is guided by goals of improved
biofidelity (human-like response to the impact environment) and reproducibility of test
results. The following criteria can be used to assess whether or not an ATD is
equivalent to the present Part 572B ATD:

               (1) Fabrication in accordance with design and production specifications
established and published by a regulatory agency responsible for crash injury protection
systems;

               (2) Capability of providing data for the measurements discussed in this
guidance or of being readily altered to provide the data;

               (3) Evaluation by comparison with the Part 572B ATD and shown to
generate similar response to the impact environment discussed in this guidance; and

               (4) Any deviations from the Part 572B ATD configuration or performance
are representative of the occupant of a civil aircraft in the impact environment discussed
in this guidance.

              (E) Temperature and humidity. Since extremes of temperature and
humidity can change the performance of ATD, the tests discussed in this guidance
should be conducted at a temperature from 66° F to 78° F, and at a relative humidity
from 10 percent to 70 percent. The ATD should have been maintained under these
conditions for at least 4 hours prior to the test.

         (3) Test Preparation. Preparations for the tests should include selection of the
test articles to be used in the tests, determination of the “most critical” conditions for the
tests, and installation of the test articles, instrumentation, and ATD on the test fixture.
Preparations pertaining to the normal operation of the test facility, such as safety



                                                          Page C - 63

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →