FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-61

PDF page 211 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 211
AC 27-1B · C-61Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

               (3)  Still image cameras can be used to document the pretest installation
and the posttest response of the ATD’s and the test items. At least four pictures should
be obtained from different positions around the test items in pretest and posttest
conditions. Where an upper torso restraint system is installed, posttest pictures should
be obtained before moving the ATD. For the posttest pictures, the ATD’s upper torso
may be rotated to the approximate upright seated position so that the condition of the
restraint system may be better documented, but no other change to the posttest
response of the test item or ATD’s should be made. The pictures should document that
the seat remained attached at all point of attachment to the test fixture.  Still pictures
can also be used to document posttest yielding of the seat for the purpose of showing
that it would not impede the rapid evacuation of the airplane occupants. The ATD’s
should be removed from the seat in preparation for still pictures used for that purpose.
Targets or an appropriate target grid should be included in such pictures, and the views
should be selected so that potential interference with the evacuation process can be
determined. For tests where the ATD’s head impacts a fixture or another seat back,
pictures should be taken to document the head contact areas.

               (iv)  ATD. The tests discussed in this guidance were developed using
modified forms of the ATD specified by the United States Code of Federal Regulations,
Title 49, Part 572 Anthropomorphic Test Dummies, Subpart B – 50th Percentile Male.
These “Part 572B” ATD’s were developed for automobile impact testing and have been
shown to be reliable test devices capable of providing reproducible results in repeated
testing. However, since ATD development is a continuing process, the standards allow
use of “equivalent” dummies. See paragraph c.(2)(iv)(D) of this guidance. Dummy
types should not be mixed when the tests discussed in this guidance are performed.

              (A) Modification for measuring pelvic/lumbar column load. Since ATD’s
have been developed for use in automobile testing to evaluate injury protection in
forward, rearward, and sideward impacts, the ATD’s must be modified to measure the
spinal load to comply with the § 27.562(c)(7). This load is influenced by a vertical
direction component and by upper torso restraints which may produce a downward
force component on the shoulders. To measure the load, a load (force) transducer is
inserted into the ATD pelvis just below the lumbar column. This modification is shown
in Figure 27.562-4. A commercially available “femur” load cell with end plates removed
has been adapted to the modified ATD to measure the compression load between the
pelvis and the lumbar spine column of the ATD. A “femur” load cell is commonly
available to most test facilities and (according to specifications) is insensitive to bending
and twisting moments. This feature prevents load transmission through the load cell as
it measures the ATD lumbar/pelvis compression forces. To maintain the correct seated
height of the ATD, the load cell is fixed in a rigid cup inserted into a hole bored in the top
surface of the ATD pelvis, the top flange of which is bolted to the pelvis.  If necessary,
ballast should be added to the pelvis to maintain the specified weight of the assembly.
Alternative approaches to measuring the axial force transmitted to the lumbar spinal
column by the pelvis are acceptable if the method—




                                                          Page C - 61

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →