FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-60

PDF page 210 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 210
AC 27-1B · C-60Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 1                                                           2/12/03


               (3) ATD head accelerations used for calculating the HIC should be
measured in accordance with the requirements of Channel Class 1,000.

               (4) ATD femur forces may be measured if desired in accordance with
Channel Class 600.

               (5) ATD pelvic/lumbar spinal column force should be measured in
accordance with the requirements of Channel Class 600.

               (6) The full-scale calibration range for each channel should provide
sufficient dynamic range for the data being measured.

               (7)  Digital conversion of analog data should provide sample resolution of
not less than 1 percent of full-scale input.

              (B) Photographic instrumentation. Photographic instrumentation is used
for documenting the response of the ATD and the test items to the dynamic test
environment. Both high speed motion picture and still systems are used.

               (1) High-speed motion picture cameras that provide data used to
calculate displacement or velocity should operate at a nominal speed of 1,000 pictures
per second. Photo instrumentation methods should not be used for measurement of
acceleration. The locations of the cameras and of targets or targeted measuring points
within the field of view should be measured and documented. Targets should be at
least 1/100 of the field width covered by the camera and should be of contrasting colors
or should contrast with their background. The center of the target should be easily
discernible. Rectilinearity of the image should be documented.  If the image is not
rectilinear, appropriate correction factors should be used in the data analysis process.
A description of photographic calibration boards or scales within the camera field of
view, the camera lens focal length, and the make and model of each camera and lens
should be documented for each test. Appropriate digital or serial timing should be
provided on the image media. A description of the timing signal, the offset of timing
signal to the image, and the means of correlating the time of the image with the time of
electronic data should be provided. A rigorous, verified analytical procedure should be
used for data analysis.

               (2) Cameras operating at a nominal rate of 200 pictures per second or
greater can be used to document the response of ATD and test items if measurements
are not required. For example, actions such as movement of the pelvic restraint system
webbing (lap safety belt) off of the ATD pelvis or movement of upper torso restraint
webbing off of the ATD’s shoulder can be observed by documentation cameras placed
to obtain a “best view” of the anticipated event. These cameras should be provided with
appropriate timing and a means of correlating the image with the time of electronic data.




Page C - 60

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →