FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-59

PDF page 209 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 209
AC 27-1B · C-59Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

              (E) Other fixture applications. Test fixtures should provide a flat footrest
for an ATD used in tests of passenger and attendant seats. Flightcrew seats associated
with special foot rests or foot-operated controls may use simulated footrests. The
surface of the footrest should be covered with carpet (or other appropriate material) and
be at a position representative of the undeformed floor or control. Test fixtures may
also be necessary to provide guides or anchors for torso restraint systems or for holding
instrument panels or bulkheads if necessary for the proposed tests.  If these provisions
are necessary, the installation should represent the configuration of the installation and
be of adequate structural strength to withstand the expected test loads.

                    (iii)   Instrumentation. Electronic and photographic instrumentation systems
are essential to properly record the information for the tests discussed in this AC.
Electronic instrumentation is used to measure accelerations and forces required for
verifying the test environment and for measuring most of the pass/fail criteria and the
floor (seat) attach loads. Photographic instrumentation is used for recording the overall
qualitative results of the tests, for confirming that the lap safety belt remained on the
ATD’s pelvis (no submarining), and that the upper torso restraint straps remained on the
ATD’s shoulder, and for recording the relative deformation of the seats as it may
influence rapid evacuation of the rotorcraft by the occupants. Paragraph d.(10), of this
guidance contains allowable seat deformation information related to an aisle,
passageway, access to exits, and so forth.

              (A) Electronic instrumentation. Electronic instrumentation should be
accomplished in accordance with the Society of Automotive Engineers Recommended
Practice SAE J211, Instrumentation for Impact Tests. In this practice, a data channel is
considered to include all of the instrumentation components from the transducer through
the final data measurement, including connecting cables and any analytical procedures
that could alter the magnitude or frequency content of the data. Each dynamic data
channel is assigned a nominal channel “class” equivalent to the high frequency limit for
that channel, based on a constant output/input ratio vs. frequency response plot which
begins at 0.1 Hz (+1/2 to –1/2 db) and extends to the high frequency limit (+1/2 to –
1 db). Frequency response characteristics beyond this high frequency limit are also
specified. When digitizing data, the sample rate should be at least five times the –3 db
cutoff frequency of the pre-sample analog filters. Since most facilities set all pre-sample
analog filters for Channel Class 1,000 and since the –3 db cutoff frequency for Channel
Class 1,000 is 1,650 Hz, the minimum digital sampling rate would be about 8,000
samples per second. For the dynamic tests discussed in this guidance, the dynamic
data channels should comply with the following channel class characteristics:

               (1) Sled or drop tower vehicle acceleration should be measured in
accordance with the requirements of Channel Class 60, unless the acceleration is also
integrated to obtain velocity or displacement, in which case, it should be measured in
accordance with the Channel Class 180 requirements.

               (2) Belt restraint system loads should be measured in accordance with
the requirements of Channel Class 60.


                                                          Page C - 59

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →