FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-51

PDF page 201 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 201
AC 27-1B · C-51Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

the dynamic characteristics of the system under test, and these characteristics are
seldom known with sufficient accuracy to achieve the response initially.

               (3) Other facets. In addition, the earth’s gravity will oppose the final
rebound of the ATD into the seat back, so that an adequate test of seat back strength
and support for the ATD cannot be obtained. The problems in Test 1, or with
rear-facing seats in Test 2, are not as difficult because the seat will support the ATD
prior to the free fall. However, the zero g condition free fall that exists prior to impact
will allow the ATD to “float” in the seat restraint system, perhaps changing position and
certainly changing the initial impact conditions if movement occurs. Again, the
development of a satisfactory auxiliary breakaway restraint system to assure correct
pre-impact condition is difficult.

                   (ii)   Test Fixtures. A test fixture is usually required to position the test
article on the sled or drop carriage of the test facility and to represent the aircraft’s
structure floor, sidewall, bulkhead, etc.  It holds the attachment fittings or floor tracks for
the seat, provides the floor and sidewall deformation needed for the test, and provides a
floor or footrest for the ATD, and it positions the pertinent interior items, such as
instrument panels, sidewalls, bulkheads, a second row of seats, if required, for
successful performance of the tests, and otherwise simulates the rotorcraft for the test.
The text fixture is usually fabricated of heavy structural steel and does not necessarily
simulate lightweight aircraft design or construction. The details of the fixture will depend
upon the requirements of the test articles, but provisions for the specified floor and
sidewall deformation are needed.

              (A) Purpose of floor or sidewall deformation. The purpose of using pitch
and roll deformation for the tests is to demonstrate that the seat/restraint system will
remain attached to the airframe and perform properly for the tests, although the
structure and seat may be more severely deformed by the forces associated with a
particular crash. Typical design deficiencies addressed by the test conditions include,
but are not limited to, the following:

               (1) Concentrated loads may be imposed on floor fittings (studs) or tracks
by seat leg attachment fittings which fit tightly or are clamped to a track or fitting, and
which do not have some form of relief (especially lateral roll relief) incorporated in the
design. These joint fittings can concentrate the forces on one lip of the floor and
sidewall track or stud and may break the joint (track or the fitting).

               (2)  Similarly, loads can be concentrated on one edge of a floor track or
stud fitting having an “I,” “bulb head” or “mushroom” cross section and may prematurely
break the flange or the fitting.

               (3) Detents, pins, or collars which lock the seat leg fitting to the floor track
can become disengaged, or the mechanism which is used to disengage the detents,
pins, or “dogs” can be actuated and release the seat as the seat or airframe deforms.



                                                          Page C - 51

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →